Models > JDB3010AWT > Instructions

JDB3010AWT Jenn-Air Dishwasher - Instructions

All Instructions for the JDB3010AWT
91 - 105 of 760
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Leaking lower inner door foam seal. Float leaking
Make sure dishwasher is powered off. Remove all inner door panel screws. Lift inner door panel upward and lean against the tub. Use a putty knife or spatula to lift old lower foam seal. Make sure door seal area is clean. Start at one end, butt new foam against the side of door and slowly pull glue strip backing while pressing foam down from left to right. Reverse door assembly.

Make sure dishwasher if off and door unlatched. Remove lower kick panel 4 screws and remove 1 screw securing float switch arm. Hold float stem with pliers and remove bottom stem nut. Remove float and re-install the new float with reverse procedure listed.
Super fast shipping on items!! Great service.
Parts Used:
Inner Door Foam Insulation Strip Float Assembly
  • Ronald from Seekonk, MA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
8 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leaked through front vent
Peeled off the old foam strip, cleaned with rubbing alcohol, let dry completely, applied new foam strip,replaced door interior done I wish repairing relationships with fiance and kids were one tenth this easy.
Parts Used:
Inner Door Foam Insulation Strip
  • mark from ardmore, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Grinding noise/dishes not washing properly. Soap not dissolving.
Other parts used:
Discharge Housing Assembly (#11)
Impeller Assembly (Wash Impeller) (#14)
O-Ring (#37)
Upper Discharge Housing Gasket (#38)

Removed upper and lower washing baskets.

Pulled off Upper Spray Arm (#33). It pulls off easily by hand. No tools required. Replaced with new Upper Spray Arm (#33) and Snap Spray Retainer (#31).

Removed Large Spray Arm Cap(#34,)which has a right hand thread. This allowed me to take the Lower Spray Arm(#2)off.
Removed Filter Guard (#36).

Next I removed the 6 screws from the Pump Cover & Secondary Filter Assembly (#4) with a Torx screwdriver. Removed Lower Spray Arm Seal(#3), Pump House Filter (#6)(which I cleaned), Assembly, Rinse Arm (#7) Jump Up Nozzle (#1). Unscrewed Discharge Housing Nut(#8) by hand. Removed Support, Wash Arm (#9). This allowed me to remove the three screws holding the Discharge Housing Assembly(#11)with a 5/16th nut driver. Next I removed the Impeller Screw (#12) with a 5/16th nut driver. You must hold the Impeller Assembly (#14) firmly while loosening the nut. Removed Impeller Assembly (#12) and Plate, Suction (#15). Cleaned out area of debris,lint, etc. Put back old Plate, Suction (#15) and replaced Impeller Assembly (#14) with new part. Replaced Upper Housing Gasket and Discharge Housing Assembly with new parts. Put back all parts in the reverse order I removed them replacing the O-Ring (#37) with a new part. This O-Ring goes in the Pump Cover & Secondary Filter Assembly (#4).

After completely assembled it ran as good as new!
Parts Used:
Upper Spray Arm Lower Spray Arm Spray Arm Snap Retainer
  • Eric from Gualala, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud grinding noise when dishwasher was draining
1. Print out the "pump and motor" exploded diagram and label the numbered parts down to #11 (discharge housing assembly).

2. Unscrew the "lower spray arm cap" (#34) by hand (it just twists off), remove the "jump up nozzle" (#1), and lift the "lower spray arm" (#2) and filter guard" (#36) out together.

3. With a torx screw driver, remove the screws holding the "pump cover and secondary filter assembly" (#4), taking note how the assembly was positioned. Be careful not to lose the two plastic "lower spray arm seals".

4. Lift out the "pump housing filter" (#6) and "rinse arm assembly" (#7).

5. With a 5/16 wrench, remove the bolts holding the "discharge housing assembly" (#11). You will likely find a plastic disk just sitting there under the discharge housing assembly. This is the source of your problem. It is the lower plate that has worn loose from the rest of the assembly and the noise is from it being ground by the impeller below.

6. The simplest fix is to order a new "discharge housing assembly" along with gaskets #37 - O-ring (for "pump cover in step #3. Mine was missing.) and #38 - "upper discharge housing gasket. Three parts to order and save your exploded diagram for when you put it back together.

7. Remove the "discharge housing nut" at the top of the old discharge assembly, lift off the "wash arm support", and put both on the new discharge assembly.

8. Insert new seals where they belong and reassemble the dishwasher in reverse order.
Parts Used:
Discharge Pump Housing O-RING Upper Discharge Housing Gasket
  • Joann from Oakland, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heard noise shorty after starting to run. Seemed to get worse at times in short time frame
Located circuit breaker for dishwasher and turned off breaker to secure power going to unit. Removed water spray bar arm inside dishwasher basin by unscrewing center nut and unclipping tabs against arm. Removed sheet metal access panels on bottom front of unit. Removed two individual plug in wires to temperature thermister. Removed 4 conductor plug wiring going to motor. Removed ground wire going to motor frame. Located plastic handle which cam locks motor / pump assembly into place. Pulled handle down gently to unlock from detent and turned clockwise to release pressure on assembly. Removed motor / pump assembly from dishwasher enclosure. Installed all new parts purchased as listed above utilizing parts breakdown aquired from PartSelect.com. Reinstalled motor / pump assembly in reverse order as listed above. Tested and ran unit with no problems. Thank You PartSelect.com, Robert.
Parts Used:
Discharge Pump Housing Motor/Pump Impeller and Seal Assembly O-RING Drain Cover Filter Support - White Suction Plate Pump Gasket O-RING
  • Robert from Tabernacle, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Front door panel had scratches and dents from the wheelchair.
Front Door Panel was replaced by unscrewing 3 screws on each left and right side of the dishwasher.

The bottom screws did not need to be completely unscrewed, just losen it enough to be able to remove the panel out.

Replace it with the new panel and screw back in the screws.
Parts Used:
Front Door Panel Insert - black/white
  • Nga from Houston, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
7 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Neither the Soap or Wax dispensors worked for years and there was water leaking from the front of the machine.
Actual i missed diagnosed the leak and ordered a very expensive door gasket. The leak was coming from shrinage of the wax resevoire o rig and the tab seal for the soap dispensor. I missed the trees the forest got in the way. The leak was dripping alond the front panel well away from the main door seal.

I cleans a the plastic surfaces and noticed a lip around the opening for the reservoire and used 150 sandpaper to remove it. Replaced the O ring, tab seal and bothe selonoids and cleaned everything. Put it back together. Works find lasts along time
Parts Used:
Wax Motor for Detergent Cup Actuation
  • JOHN from PALM BAY, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Not washing properly. No water shooting through the jets
It takes about 5 min. to disassembled the lower jet system. As you disassemble, make sure you clean all the filters, and asses the integrity of the filters. If they are broken, you need to replace. Once you get to the impeller, you know it is broken because the lower part is loose. To replace you need to firmly hold the impeller as you unscrew the top screw. If the housing gasket is broken or too loose, replace. Otherwise you will have leak. Refer to your models diagram for proper assembly.
Parts Used:
Impeller Assembly Upper Discharge Housing Gasket
  • Manfredo from Palm Beach Gardens, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
6 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the soap dispenser door broke off, I lost the pins and the spring.
The repair is fairly simple except that the diagram on the web site has an error - it reverses the positions of the long hinge pin and the short pin. I kept trying to do it as the diagram showed and of course it didn't work. Then I followed my instincts! The only other difficult part was figuring out which way to insert the spring but there are only a few options so trial and error was the simplest way.
Parts Used:
Short Dispenser Door Retaining Pin Hinge Pin Detergent Cup Lid Spring Detergent Cup Lid
  • Bonnie from South Orange, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    Less than 15 mins
9 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The lower dishwasher rack was rusted out
We ordered the replacement part for our Maytag model and when it came we saw that it was different than the original part. The original part had 8 wheels with a higher left hand side. The replacement part had only 6 wheels and no higher side. The replacement part would not pull in and out evenly and was a bit too narrower. We called Parts Select and told them our problem and they are going to refund us in full and take back the part they sent. Alas we will have to buy a new dishwasher. We would use Part Select in the future for replacement parts.
Alice
Cambridge, MA
Parts Used:
Lower Dishrack with Wheels
  • Alice from Cambridge, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaks out and below the front door
First of all, rather then spending the 44 dollars on the main door seal simply cut yours in halve and trim a quarter of an inch from the disintegrated ends and use superglue and glue these ends together. this glued end will now be up top and in the middle and new clean ends will be down in the corners. next I removed the plastic door panel using a torxhead screwdriver, I just stuck the new inner foam pad on the old one. Then I glued rubber washers to the inner frame about 1/8 thick in the top 2 corners only. Finally I reattached the plastic door being careful not to tighten the torx head bolts just tight enough. It's dry and working good.
Parts Used:
Inner Door Foam Insulation Strip
  • John Todd from Franklin, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
7 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
original basket fell apart
threw out the broken and put in a fantastically improved new one. very easy (would have done it sooner if I'd known it was that simple to find it online and order it) thanks
Parts Used:
Silverware Basket - Gray
  • D from Villas, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking from the dishwasher on left side
Took off the float, the jam nut was hard to get off, we ended up breaking the bottom piece of the float to get it off, but that was okay because we had a new float. The new float went on real easy and the jam nut went back on real easy. The foam insulation strip was real easy to get off we got a good hold of one end and striped it off slowly so there was nothing left on the door, then we cleaned the surface and put on the new insulation strip. We ran dishwasher to test it and there was no leak. Awesome. Cheap and easy to repair. We were impressed.
Parts Used:
Inner Door Foam Insulation Strip Float Assembly
  • Theresa from Zimmerman, MN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
water leakage
slid the part in the groove (left side)
Parts Used:
Water Deflector
  • maria from Ruther Glen, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door leak and leak on inlet valve
I replaced the door latch grommet just as everyone else has described on this site. It was pretty easy. I was amazed that such a little piece of rubber can let so much water get by. The inlet valve was not too bad either. Take the two bolts out that hold the bracket to the dishwasher. Remove the rubber hose on the back side and take loose the two electrical connections. My water line was long enough to pull it out in front of the dishwasher. Then I took the water line loose and removed the fitting. Installed the new one in reverse order of what I just described. These items took care of the bulk of the leaking problem. But I am in the process of ordering a new door seal which I hope resolves the rest of the issue. Also make sure you check the upper and lower control arms to make sure the spray holes are free of debris. This dishwasher was full of pieces of clear plastic that caused the spray arms to spray indirectly and towards the cracks of the doors.
Parts Used:
Dispenser Door Latch Grommet Water Inlet Valve - 120V
  • April from Valdosta, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the JDB3010AWT
91 - 105 of 760