Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.
With circuit breaker off, I opened the oven door and removed the two mounting hex-head screws that held the cooking element at the rear of the oven. I pulled the oven away from the wall and unplugged the unit's 220 volt power cord from the wall. I removed the rear cover panel by removing five hex-head screws that held the panel in place. I sought out the wires that connected to the oven element and pulled the tabs from the failed element. I moved to the front of the stove to remove the old element. As the contact ends of the element are curved up, I needed to lift the front of the old element up to an approximate angle of 45 degrees before I was able to remove it from the oven. I then placed the new element into the mounting holes, again with the front of the element raised at an angle. Its insertion was easily performed. I replaced the main element mounting screws at the rear of the oven. I went to the rear of stove again and reconnected the power tabs to the element contacts. I repositioned the rear cover panel and replaced the five hex-head screws to secure it into place. The main power was reconnected to the power outlet and carefully slid the stove back into position. Circuit power was reset and the oven tested successfully.
This door required a lot more screws to be removed in order to remove the inside window assembly. I counted a total of 19 screws. That is why the estimated time is 30-60 minutes.
- remove door from range following the basic guide to removing any range door. - place door on work surface with the outside facing down. - remove three 1/4 socket screws from bottom and two star screws on top. - Flip door over, remove outer door panel and set aside. - There will be a separate pane of glass that needs to be removed. Remove 1/4 socket screws holding glass and set aside. - Slide door over your work surface edge so you can remove the star screws holding the door hinges (from underneath). You could flip the door over but the door would have to be flipped back once the hinges were removed. - Remove the remaining 1/4 screws holding the aluminum shielding. - Remove the shielding being careful not to disturb the insulation around the window. - Remove the damaged window. Take note of the writing and orientation on the aluminum window frame. (upper right if hinges were on the bottom) - Set the new window in its place. - Reverse the process by replacing the aluminum shield, hinges, than internal glass pane. - Set outer door on top and holding everything together, flip door. - Tighten the two star screws on top and the three 1/4 socket screws on the bottom. - Replace door. Don't forget to lift up those hinge tabs before trying to close the door. All done. Pat yourself on the back for a job well done.
When my wife tried to get the oven door apart to clean behind the glass front, she bent the Door Bottom Channel Trim, so I had to order a new trim piece.
Consult the instruction guide that comes with the new part. Excluding doing some cleaning while things were apart, the operation took about 20minutes. 1. Open the oven door all the way. 2. Pull back the hinge latch on each hinge. 3. Close the door partially (about broil position). 4. Remove door by pulling so that hinges com out of the slots. 5. Carefully set door face down on a table so that inside of door faces up. 6. With a Torx driver, remove 2 screws at upper part of inside of door. 7. With a nut driver, remove screws at bottom of Door Bottom Channel Trim. 8. Lift inside of door off, being careful not to lose the spacers that are behind the door panel at the upper part of the door. 9. With the nut driver, remove 4 screws that hold bottom trim to the side trim pieces. 10. Remove the old trim and replace with the new. 11. Align the left, right, and bottom trim pieces. 12. Reattach the 4 screws that hold the bottom trim to the side trim pieces. 13. Carefully replace the inside door panel, making sure the spacers are aligned properly between the main door pieces. 14. With the Torx driver, replace the 2 screws at the upper part of the inside of door. 15. With the nut driver, reattach the bottom screws at the bottom of the trim piece. 16. Carefully reinsert the door hinges into the slots (the door must be in the approximate broil position). 17. When hinges are properly inserted, door may be opened all the way. 18. Push the hinge latches back into hinges to secure door to oven.
shaft of switch broke and old model oven had part number problems.
unplugged oven, pulled from wall, removed panel, removed switch, read directions, modified new switch, installed new switch, cleaned behind oven, and back in service.
I unscrewed and removed the old element from inside the oven, but unfortunately there wasn't enough extra wire to pull through and attach the new element from the front, so I had to move the oven away from the wall, remove the back panel, and connect the new element from the rear. Very self-explanatory.
The new element had some kind of spray or coating on it that caused some smoke for a few minutes, but then it worked fine.
1. Shut off power at breaker. 2. lift and prop up burner panel (top of stove) 3. removed three screws along top edge. 4. remove oven door (lifts off hinges easy) 5. remove 4 screws along upper oven opening 6. remove 2 screws up under front panel and pull out upper panel enough to access back of switches. 7. unplug wires (5) one at a time and plug onto new switch. 8. remove the two screws from front holding switch in place and remove old switch. 9. install the two screws attaching new switcj. 10 replace all screws in reverse order. 11. Re-install door. 12 close breaker easy job any one with any mechanical no-how can do.
I pulled out the drawer and inserted the new support. This one inserts into the back of the drawer as opposed to the sides. I had ordered two of the replacements even though I only needed one and decided to replace both. I think it was a good move as the drawer works better than when we first got it. Just one simple screw made it complete.
After receiving the new swith from part select in less than four days with surface mail as they promised, it took me less than five minutes to replace the new swith with the old one. The only tools that I needed were A) a 5/16 nut driver to remove the back panel in order to get an access to the swith.B) a phillips screw driver to remove the swith assembley from the front panel.
I had an estimate from a technician to do the job for 196.27 dollars!!!!!:(:(. I only paid 29.56 Dollars to part select to get this swith, including the shipping.:):):)
Broiler shorted out looked like a 4th of july sparkler.
Ordered on Tues got part on Thurs used a nut driver removed 2 screws holding element in top of oven,then removed the 3 screws holding the element and thermostat to rear of oven pull about 3 inches of slack, removed the blade plugs from element placed them on the new element and assembled it. Took abou 30Min. Easier if you remove the oven door!
First thing I unplugged the range. Then I unscrewed 4 screws in the back of the stove to take the back cover off. Then inside the oven, I unscrewed three screws to lossen the element. Then disconnected the two wires from the element.
Then replaced the old element with the new one going exactly backward as mentioned above finishing with plugging the range.