JBC2088HTW Jenn-Air Refrigerator - Instructions

Broken lid popped out, new lid popped in. No tools required. 30 seconds to replace. Great price, part shipped within an hour of placing my order and arrived the next day, although I only paid for standard shipping. Excellent service - will definitely order again if the opportunity arises!

removed the old valve from back of fridge by removing screws that held mounting plate. removed water lines by pushing in on quick connects and pulling hoses out. A little different type of connections. installed new valve and pushed hoses into connections making sure that they snaped in. reinstalled screws and checked for leaks. took about 15 minutes!

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

Easy repair. Unwrapped the new cover; pulled the old one off by releasing tabs. Inserted new piece.
Took less than 15 minutes. Looks like new. The replacement part arrived quickly from Part Select.

I searched in line for a replacement fill valve and easily found it on your site w/ excellent diagrams. I turned off the frig., & the part came out simply and logically first removing the 5 screws that hold it in w/ a nut driver. Then remove the supply water line and the other quick connect lines that feed the ice maker and the chilled water dispenser. Then, disconnect the two wire harnesses that clip off easily by hand. They feed the two relays in the valve and are color coded. Remove the valve and reverse the procedure to hook it back up. Note: a little water will come out of the lines so be ready w/ a small bowl and a dish towel. After installing the new part, it was necessary to "bleed" the water lines of air by drawing a few glasses of water from the water dispenser to get the system operating normally again. One tool, common sense, 30 minutes. Probably saved $150 + on a repair man plus parts markup. Thanks very much!!

followed the instructions provided and that's it!

Very simple. Matched female plugs with respective male color coded prong; pushed together then inserted unit in slot of freezer sidewall and rotated into position...job done.

pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh

Removed broken lid and snapped new one in place.

You will need a Nutdriver a 1/4" size and a philips screwdriver, I'm a young woman, It was easy find the pc. I need here since I lost my manual, in this particular piece the inside part is not included the tab that controls the tempeture, you will have to use the same from the broken one, snap off all and carefully remove it from the insideout of the broken piece to intall it in the replacement, make sure you remember how its going back, that was the hard part of all the repair! after that it was easy as 1, 2, 3!!! have fun!!

First I removed the six screws from the cover. I then disconnected the two wires and pulled the small motor out with its base and removed two screws that hold it in place. I then changed the old one for the new one and set it back in its place. I then set the cover back and turned it on. I was happy again.

Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.

R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin

Plied off the relay switch with a screw driver. I could not pull it off by hand. Disconnected the wires to it and replaced with new part. Had problem getting the part back on and lining up the pins with the connector. I had to line up one pin and start at an angle and roll the part onto the contact pins.
I was impressed with the one day delivery without paying because it was shipped from a warehouse in California where the repair was made.

Unscrewed back of fridge and unplugged relay from compressor and plugged in the new one remember that the new one turns 180 degrees from existing switch.