Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Element burned into.
First I removed the two screws that held the element in place. I pulled the element out about 2-3 inches and then removed the two screws that fastened to the ends of the element. Was careful to keep the same wires separate in order to fasten the new element back to the same two wires. When fastening the new element ends back to the wires, care must be taken to not bend the ends of the element when tightening the small screws to the ends. Everything went real good and am most pleased with the very fast service portrayed by Parts Select. They are a class act company and rate very high in customer satisfaction!
1. Removed the back panel. 2. Disconnected the wires from the old switch while connecting wires to the new switch one at a time. 3. Installed the new switch and broke off the excess metal on the post which fits into the burner knob on front of the range. 4. Replaced the burner knob and replaced the back panel.
Successful repair to Our GE range, manufactured prior to 1965 (when installed in house). Pulled range from wall, unplugged, removed burned-out broiler element. Previous check with GE to make cross reference of range part number to Part-select part number for this nearly 50-year-old range. Obtained new part and installed. Works. Range has self-cleaning oven, accidentally destroyed thermal switch attached to element mounting bracket, difficulty with frozen mounting nut. Self-cleaning still works; thermal switch locks out a solenoid which defeats door latch; prevents premature opening of oven door when oven too hot to open safely. Internet search did not find GE part but there are generic devices of the same type available; will consider installation later.
Easiest repair I ever did. Killed the circuit breaker, then removed the oven door, loosened the 2 hex nuts with a nut driver, pulled the old element out a few inches, loosened the nuts holding the wire to the element. I then put the new element in place, connected the wires to the element, pushed it back in to the insulation, and then replaced the nuts on the cover piece. Put the circuit breaker back on, and done!
1] removed door and put it on bench 2] removed two[2] screws to open up face of door 3] wedged aa 2" x 4" between face of door and back of door 4] used nut-driver to remove the damaged end-cap [this part holds the stove handle in place] 5] put handle on one side to good end-cap and slipped new end-cap on handle and put it opening where old end-cap came off 6]screwed in new part and screwed together face and back of oven door 7] put door back on oven
Turned off the power. Removed the screws holding the built-in oven to the wall. Slid out the oven. removed the four screws that were holding the inner oven walls to the outer oven walls. Slid the inner oven wall out 1/4", removed old gasket material and replaced with new gasket. Slid the inner oven in tight and replaced the screws.
I have a 22 year old GE double oven with a range top that I can't live without. I do alot of cooking, baking, and my share of entertaining. To replace this oven I would have to sacrifice having 2 ovens...or remodel my kitchen and reposition their location. So when something goes wrong with this oven I cringe. It needs to keep ticking for another 10 years. A friend recommended PartSelect. looked on line and found the part resembling mine. I called just to confirm the part was correct, and found out it was not. I looked up the part number the said was correct but the shape was wrong. I order it anyhow and when it arrived it was what I needed. The picture on the website was inconsistant with the part number. So I'm really glad I called and spoke to a rep. The part arrived in 4 days and the next day I installed it, needing only one tool. Doing it myself saved me a few hundred dollars and my oven works great again. And their price was lower than a local parts dealer. I added PartSelect to my favorite list for future needs! Thanks!
Unpluged range. Removed back cover to access the infinite switches . removed old burner and drip pan. removed terminal block and retaining screw on cooktop. removed terminal block wiring from infinite switch taking care to mind were the wires came from. Install new terminal block and reattached to cooktop . installed new 8" burner and drip pan reinstalled back panel and plug in electrical to unit . tested burner . replaced stove after verifying burner worked
I could not change times on the analog clock, and when using pliers, the knob broke.
The replacement was a digital clock instead of analog. The directions were a little confusing, but adequate for the change. We removed the old clock, and followed the dirctions for replacing it. We made three tries to get the wires correctly connected and on the third try, it worked fine. However, I had to return the three knobs since the digital had push buttons. It fits into the space perfectly and we are very happy with it.
scissors and opened bag. determined that all three knobs were identical. aligned slots on each knob with flanges on each shaft. snapped each knob into place. Did a happy dance of empowerment around the kitchen. ( knobs had been broken for at least 5 years). used timer to avoid burning christmas cookies. Have a Merry one!!!
Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.
The Drip pans were unusable due to excessive use, and I decided to replace the Surface Elements as well.
There was nothing to it...I unplugged the Sufrace Elements from thier bases, removed the Drip Bowls, replaced the Drip Bowls and then plugged the Surface Elements back in to thier bases. The entire process could not have taken more than two minutes.
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
First turned off the circuit breaker. The two screws holding the element in place were removed. Next the element was pulled out about 3 inches. Wires were disconnected. Old element was removed. Wires were then attached to the new replacement element. The element was then re-attached to back of oven, using the two screws. Circuit breaker turned to on. About 5 minutes. Took longer to change the flashlight batteries!
