JB710SK4SS General Electric Range - Instructions

Removed top back plate of oven. unpluged all of the wiring plugs on the control board. Removed two screws on the control board. Removed face plate from old control board and put it on the new control board. Atteched new board with the two screws. Connected all of the plugs to new board ( all plugs are color coded to board). Re-installed oven back plate. Pluged oven in. Works great.

I called my dad and he came right over and fixed it. He is a super dad!

Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.

Followed the instructions that were sent to me by E-Mail.

a) Turn off 240v ckt brkr to the oven p b) In the Rear -Remove the 6 hex screws holding the protective covering c) Remove the two push-on terminals p d) In front, open door to range and remove the two screws holding the faulty bake element p e) Remove faulty bake element and replace with new one f) Replace all screws p

Remove burnt coil and replaced with new coil

ordered both elements to be sure , as they were not that expensive , remove back plate from range , to expose conections , pull off connectiion wires , open the oven door and unscrew with nut driver , follow the same seqence but in reverse put the new elements in . And there you go you have just saved yourself about 100 dallors , by doing it yourself .

Turned circuit breaker off to the range, removed both oven shelves. Removed both screws securing bake element to rear wall of oven with nut driver and pulled element carefully away from mounting location taking care to ensure that the attachment wires remained connected. From instructions previously read online, the wires do not have a lot of slack and if not careful, once disconnected, they may spring back into the insulation and require some fishing around or even having to pull out range and sort out the wires from the back side. Since the wires are attached to the element with push on terminals, I used locking pliers to slide the terminal off an ensure that I had a firm hold on the terminal such that I would not lose the wire end into the insulation, that was a helpful hint. Once the old element was removed it would have been a simple reversal of the process to install the new element, if my wife hadn't looked at the progress and decided that I had to give a thorough scrubbing to a "self-cleaning" oven, that took the majority of the 15-minute time. One side comment: This site saved me a lot of time by reading other people's experience and by a easy order process with prompt delivery.

1. Turned Off Range Circuit Breaker. 2. Take Door Off of Range. 3. Removed Both Racks. 4. Removed Both Screws on rear of oven. 5. Pulled stove all the way out. 6. Removed 5 Screws on the Rear Electrical Connection Cover Panel. 6 Remove 2 Clips from Bake Element. 7. Remove burnt Bake Element. Install in Reverse Order.

Pulled oven out from the wall and removed just the center section of the back that allows you to see the wires and not allow them to pull through. Took the two screws out from the inside of the oven that held the bake unit in place and after unhooking the wires from the back pulled the old bake unit out through the oven and inserted the new unit and fastened in place with the two screws. Then refasten the wire connections in the back of the oven and replace the rear panel. When removing the old burner from the inside lift it up and pull out. Previous ovens I had owned just plugged in and removed from the inside. This model is fastened. Other comments were helpful to me too.

Step 1. Turn off the breaker to the range. Step 2. Pull the range out from the wall. Many of the installation instructions recommend accessing the element from the front only and to use clips to keep the wires from popping back into the insulation. My recommendation is to just pull the range out and take off the back cover. This is much easier than worrying about losing the wires. The connectors will be easy to access from the rear. You know you need to clean behind your range anyways. Step 3. Remove the back cover of the range. Step 4. Disconnect the two wires that are attached to the lower element. Step 5. From inside the oven remove the two screws holding the element and remove the element. Step 6. Insert the new element and reinstall the two screws to secure it. Step 7. From the back of the range reconnect the two wires to the element. Step 8. Reinstall the back cover. Step 9. Turn the breaker back on. Step 10. Test the new element.

Control unit was easy to remove ,wires color coded-the face plate(key pad) needed to be separated from the old unit. Carefully used a hair dryer to warm the decal. . . Secured the old unit gently in a vise, warmed ( and separated slowly, with a razor blade and thin putty knife(patience). . Once removed, applied to the new unit. . . 5 Stars to partselect for service. . . . Turned a $400 repair into $100 do-it your self. Partselect will be my 1st "go to" from now-on.

Took two nuts loose disconnect electric connect new element reinstall screws

Replace control switch

Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later. Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!