JB553GM1 General Electric Range - Instructions

Watched the video on the PartSelect site. Could not have been an easier repair and I saved the cost of a service call - probably saved at least $100 - $150 in service call and I can only guess what the labor cost would have been. Will use this business again for other appliance repairs on my older stove, washer, etc. By the way - the official Kenmore site said this part was no longer made and unavailable --- Thank you PartSelect for having the part and saving me the cost of buying a new stove!

Unplugged over and remove oven racks. Dry fit new clips to hold up broiler element; using piers to insure secure fit to the element. Removed screws that hold element and attached clothes pins to wires to keep from falling back into the oven. Removed element from wires. Secured new/replacement element to wires removed clothes pins. Position element to be screwed into back of oven. Screwed into oven attached clips to oven and element. Plugged stove back into outlet. Turned oven on to test. Worked job done.

Called in and talked to someone and he look yup what he thought was correct but after i got them theywere wrong so i sent them back for a full refund minus 9.90 freight. I still need to figure out what i need for my 27 inch wall oven. Please help. Thanks

It was very easy than i expect,
Just pullout the stove from the location to access rear side of stove,
unscrew 3 nuts with socket rench and disconnected wire. Opened front door of stove, unscrew 5 screwss , then pulled out broken element, replaced it with new one.
It is very very easy , Dont be affraid do it yourself.....

Lifted the door off the hinges, unhooked the spring from each hinge, unscrewed 3 Phillips head screws from the face plate of each hinge and removed the hinge assemblies . Hinges went in the way they came out; easy shmeasy. Took less than 15 minutes and the door is like new.

1. Slide oven door off hinge arms and set aside
2. Slide out oven bottom drawer and set aside
3. Detach springs from perforations in stove rails then hinges and set aside
4. Loosen three screws in each hinge, remove and set aside.
5. Remove hinges, threading them out through openings
6. Thread new hinges into stove openings. Align hinge arms with hinge wheels.
7. Align and tighten three hinge screws in each hinge.
8. Re-attach springs to perforations in hinge, then stove rails
9. Slide oven drawer into stove and door into hinge arms

ordered parts WB21X5301 oven sensor and 2 WB1X681 screws mine were bad highly recommended slid my stove out also a good time to clean all the years of junk behind it removed screws mine were bad unplug the connector slide the sensor cable through the hole and u are good after cleaning be hind stove slide back into spot reinstall power and code went away tested different temps with temp gauge and keypad and we were good

Disconnect power to burner module. Dissassemble module with nut driver. Screws connecting feed wires to burner were too corroded to remove. Cut wire close to screws, stripped insulation and inserted new ends into new burner. Reassembled module with nut drivers.

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

Remove oven door from hinges, by pulling it straight up and off, (like you would do for closer access to clean inside). Remove the storage drawer. Lift up and away off the track, (like a file cabinet drawer). With the drawer out and away, you can see how the springs are easily detached from each hinge. Note the location of where the springs attach to the hinges, and bottom of stove. Remove each spring. Three screws on each side hold the hinges on. Unscrew, and set them aside. (The new hinges did not have new screws in package.) Place new hinge in place. Reinstall in reverse of disassembly. If any part of the door or face of the stove (where hinges mount) was bent slightly due to forcing door open, reform with light hammer taps and C-clamps. Enjoy for ANOTHER 10+ years, because it's a GE Profile Stove : )

After tilting the oven door out and sliding it up to remove it, I slid the storage drawer our completely from the range. After removing the spring that held the hinge assembly under tension, I removed 3 phillips head screws that held the existing assembly in place and removed it. After verifying the part you sent was an exact match, I reinstalled the new part, fastened the screws, attached the tension spring, installed the storage drawer, and then slid the oven door back in place on the brackets, completing the repair.

With multimeter checked resistance of oven sensor. Specs called for 1100 ohms. It was off by 27 ohms. The sensor from Part Select had exact wire connection as original. Then just matter of undoing old and reconnecting with new one.

One unsatisfactory event. I asked Part Select why my clock did not work or light up(timer works ok) . Answer was: sorry we have no time to help you. That soured the otherwise happy experience.

Followed the excellent removal and installation video by PartSelect. Also the diagram was excellent allowing me to purchase the correct hinge the first time. Fast shipping.

REMOVED DOOR TO OVEN
REMOVED HINGE [3 SCREWS]
REMOVED BOTTOM DRAW
UNHOOKED SPRING FROM LEFT SIDE ATTACHED TO HINGE
PULL OUT DEFECTIVE HINGE
REPLACE WITH NEW HINGE AND SCREWS
REHOOK SPRING TO HINGE & REPLACE DOOR
COMPLETE

FOLLOW VIDEO PROVIDED BY PARTS SELECT

Remove the two screws from the back wall holding the element. Remove from the three clips holding the element up and pull forward slightly. Remove the clips from the ends of the elements. Put back in reverse order.