Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Halogen element staying on
removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires. Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.
Knob/switch would not turn right front burner on at all!
Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!
Wire connection from the oven was too small and I had to make it larger with a flat head screwdriver and pliers. I used a head flashlight for I could see better. I would suggest not having a glass of wine before starting the repair. It would have only taken me 15 Minutes instead of 30.
The small element blew out consequently shorting out the infinite switch.
The very first thing we did was turned the circuit breaker off and unplugged the range. My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.
no power going to burner when switch is on, switch bad
I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My knob fit on the new switch without any of the parts that came with the switch.
The baking element burned through, in my really old double oven. (It was in our home when we bought it 16 years ago.) It was the top oven element that broke. I wasn't sure it could be repaired. I looked on line and I found it. It took my husband less than 30 min. to fix it. I have my oven back but it would have nice to get a new one.
Burner only worked on High and very low temperature setting.
Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.
Repair job was easy but longer than the 15 minutes that it said it would take.
First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.
We just remove the old surface unit and insert the new one by hand. Thanks to PartSelect, we were able to buy really good quality part that works right away! It was a 26-year-OLD GE Stove/Microwave space maker, the parts were hard to find in stores. Thank you for selling this! All the best for your business!
