GU2275XTVY1 Whirlpool Dishwasher - Instructions

Turned off power, turned off water supply and diconnected, slid out dishwasher. Removed the spray wand and tilted dishwasher to access the two nuts and disconnet the wires. Removed the two nuts using a socket. Removed the old heating element and replaced with the new one secured with new nuts ( the old ones were fine but since I bought two new ones why not). Pluged the wires back up slid the dishwasher back in hooked up the water reinstalled the spray wand cut on the water and power. Good as new.

After I took apart the inside of the door, removing 12 star screws, I was able to see the inside of the automatic soap dispenser device. Since I now had the new device to look at, I was able to replace the latch pin back in the existing device and it worked!

I now have a replacement if the device actually breaks in the future and looking at the small plastic pieces, it will probably happen sooner or later.

Removed the Bi-Metal fuse and ordered a new one and recerved it two days after ordering. Replaced it and it worked.

Removed dishwasher from under the counter and took it to my shop. With the washer on its side, I removed the motor, then the impeller and seal. I then disassembled the motor and replaced the front bearing(purchased separately). This required an arbor press. I then reassembled the motor and installed the new seal and impeller. Reassembled in reverse order. Reinstalled under the counter and made conections. Checked for leaks and proper operation.

My KitchenAid dishwasher's upper dishrack had several places that were completing rusting out, just leaving the skins of the plastic coating in place. I ordered the upper dishrack - just the dishrack, none of the clips or other items shown in the schematic - and installed it pretty easily. One caution - this is JUST the upper dishrack. If you have two rows of tines that are clipped in and flip-flop back and forth on the left and right wider sides of the rack, you will need to order one or two pieces of part # PS 898500 as well. One of my tine rows was in salvageable shape, so I only needed to order one (in a second order upon discovering I it wasn't included). It wasn't difficult to figure out how the clips could come out and snap back in place. Just be careful, know that these are just plastic items and can break easily.

Disconnected the power and hot water supply.
Removed mounting screws under the counter, and the lower panel screws to expose the leveling screws.
Backed the leveling screws up so that the unit would slide out more easily
Walked the unit out to where I could reach the back side.
Disconnected the two power wires from the heater coil (slide off)
Unscrewed the plastic nuts holding the heater in place and removed the heater coil.
Replaced the heater coil and nuts.
Reversed the process above to install.

Take 10 lower star srews from inside of door (5 per/side) that hold on front. Remove front door panel. Remove 6 screws in detergent dispenser and replace.

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

Make sure you order 2. One on each side

I just placed the cap back on, it worked great, fit fine and so glad I found this part. I was thinking of ways to McGyver it, thinking it would be impossible to find a new part. Glad i fount this site and the part.

I simply pulled out the old gasket and pushed the new one in with my fingers. I had to trim about an inch off the length with a utility knife. The seal is nice and tight now and we have no more water leakage.

After reading other posts I opened the dishwasher door put a support underneath it. Knowing that all the screws were not the same I carefully unscrewed them and placed them on a towel in order of extraction. After all the screws were taken out, I lifted the door up gently and lifted it out of its place and put it aside. Now I could see the hex screws holding in the soap dispenser. I then unscrewed the screws and place the frame aside. Next I gently pulled the electrical connector to the dispensing unit off. After locating a snap tab on top on the left hand side and one underneath on the right hand side, I gently lifted the tab and the dispenser unit moved slightly forward. After gently prying the lower tab on the right hand side the dispensing unit was loose. I just reversed the process to put things back together. I was not necessary to have any help taking things apart but it was very helpful having a second set of hands when we put it back together. Lining up the screws for the door was much easier with two people. After installation, I started the dishwasher to check for leaks. Everything was fine. Very satisfied to be able to repair/replace this unit without calling a tech. If you can change a spark plug on a lawnmower you can replace a soap dispenser on a dishwasher such as mine. Very quick delivery from parts source. Thank you.

Soap dispenser unit could have been repaired by pushing the plastic arm back home and adding two drops of instant glue to keep the plastic shaft in proper place. Didn't need to purchage a new unit.

The upper spinner was laying in the top washer basket. I went online but no help was avaiable. Went to store where we purchased dishwasher and they gave me part number to order but not online I had to call to order. Part arrived in about three days. I took two screws loose on the top of dishwasher removed broke retainer to put new retainer in but I drop it into dishwasher so you have to me very careful
so I tried to order just the retainer but is not sold by it self. Had to order whole new kit. Other than that it is easy dishwasher runs like a new one.

Remove front door panel, replace B-metal fuse.