GR556LRKB0 Whirlpool Range - Instructions

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

I read it may be the temp sensor. Ordered a new one. Took a minute to undo three screws holding the back on, and one screw for the sensor. But still didn't work. Then realized maybe the oven was changed to Celsius. In manual - open door, hold broil for seconds and changed back to Fahrenheit.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I screwed the light lens into the socket and went beautifully. Better than the original. (I am a retired, 75 yr. old woman).

After some major troubleshooting and "some" help from support folks at fixya.com I was able to pin the problem down to a blown thermistor. The repair was very simple - pull the back plate off and remove the two screws holding the thermistor in place. Replace thermistor and test both heating elements. I assume during the cleaning cycle the thermistor was over heated. Makes one wonder if it was a faulty thermistor or will it happen again on the next cleaning cycle.

Had already removed back covers and disconntedted power. When io received parts I replaced them in reverse oder I had removed them. Took me longer to replace back covers because of my bad diabetic hands. Thanks very much, yopu savbed me a bunch. God bless you and yours, god bless america.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed broken glass cover and bulb, cleaned old gasket off with damp cloth and replaced with new bulb, glass cover and gasket. No tools needed.

Repair was very straightforward. Based on information gathered from an earlier post about the same repair I simply removed all screws from the oven door. These were all located on the bottom edge of the door itself. Upon removal of the screws the door separated and exposed the "core" where I then had access to the hinges which were held in by one screw each. I removed the broken hinge, replaced it with the new hinge, pieced the door back together, put back all the screws, and the repair was complete.

Unscrewed about 10 screws to disassemble the door to get at the hinge then screw new hinge in. Was inspired by the woman who said she did it while watching a child. I saved $200 in the repair fee I was quoted

Removed two screws bottom front corners of range top - propped the top up - removed the wires from the element - removed the old element - installed the new element reattached the wiring reattached the hold down screws and bingo it worked!

First thing to do is turn the 220volt electrical circuit breaker to the unit off and the last thing is to turn the breaker back on!

Your online video was a great help.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilitate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.