GLEB30M9FBC Frigidaire Microwave Oven Combo - Instructions

I replaced the bulb using my hands to twist the bulb in the socket located at the top of the refrigerator.

Disconnected the power cord, removed the outer cover, shorted the two terminals of the high voltage capacitor with the blade of a screw driver with well insulated handle (very important to prevent a bad shock!!),;removed the plastic fan housing for access to the grounding screw and capacitor housing, installed the new capacitor with the reverse of the above steps (but don't reconnect the power cord yet!!}
Now, the most important step of all, reach inside the oven and remove the mica wave guide cover, clean the oven walls thoroughly and clean the inside of the wave guide with clean cloth and water, sand to bare metal any carburized spots on the exit of the wave guide, cut out any carburized spots on the mica cover, replace the clean cover , or order a new one if necessary. It is OK to use the microwave without the cover while waiting for shipment of the replacement mica cover, but be absolutely sure there will be no food spatters on or near the wave guide opening.

Remove microwave from wall, removed outer cover which allowed access behind the control panel, was then able to take out the broken lever and with a little maneuvering was able to replace it with the new one. The whole process took less than an hour and was easy to accomplish.

Very easy just had to pull the wire up that holds it secure.

It was really easy just unplugged it took off the back cover changed the part out put back cover on plugged it in and the elements were working great!

I usually try the cheapest part to replace when I come to a fork In the road but I wasn't home at the time and my other half called in the "expert". He said it was the clock timer and it would be $450 to replace it. She sent him away and I bought one online for $200 and put it in only to find out that it didn't solve the problem. Did some reading and found out that it could be the sensor. Put an ohm meter on it and found that to be the problem. Left the new clock timer in it anyway so now we're good for another 100,000 cookies or 1000 pizzas, which ever comes first

Pulled range out from cabinet, removed back plate, two screws inside oven attaching the temp sensor. Then pulled the sensor and wire through from back. Reverse to replace about Ten minutes
OEM parts plug in same, works great

1 Turned off the oven breaker.

2. Removed the oven racks.

3. With a Phillips screwdriver, removed the mounting screws holding the temperature sensor and unplugged it.

4. New sensor plug did not match 20 year old connector. Had to cut and solder splice the connectors.

5. Installed the new sensor and now oven holds temperature steady.

Easy order, quick delivery and easy installation, happy wife.

Phillips screwdriver used to remove 2 screws at top left in oven. Pulled thermostat out until I could get to the connector. Used pliers to hold wire, reconnected new plug , threaded it back into back of oven and reattached the two screws.
Saved $150 on a service repair call.

Plastic trim on inside of the door pops out if you pry with a flathead screwdriver. Then lift door latch out of place and carefully remove the spring. New latch goes back in the way the old one came out. Door trim pops back in.

Removed the wires that I could, then terminal block. Installing the new terminal block was very easy; however the wires that arced were fused to the terminal bock screws and needed to be cut and new connectors had to be put on the wires to allow them to be reattached to the block safely.
Once all was replaced and reinstalled the oven has worked great. The length of the repair was increased because of the melted parts and having to run to the store to get the new wire connectors big enough to fit on the wires. If we were simply replacing the block and had not encountered the melted ends, it would have been a very quick and easy repair.

2 screws disconnected old one and pulled out the new one in put in opposite way. The representative was so helpful, part came fast. thank you

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

unscrew the sensor inside the oven; took off the back of range to access harness of sensor; the replacement part harness did not match up to the original, so we stripped the clip from the end of the part and also the end of the harness in should clip into. after joining the wires together with ceramic wire nuts we tested the oven to make sure all worked AND IT DID!

my original part arrived and it did not fit. When I called to explain the problem I was told it was the wrong part. The big problem is... Frigidaire calls the receptacle a terminal block kit as well as a terminal block kit which is a totally different part. I tried to explain that to several different folks I spoke to at your company as well as Frigidaire but I'm not sure if I got that point across. Take a look at part # 530 393 5058 and part # 530 440 9888 and you will see that they both mention terminal block kit. Hopefully the part I am getting from Frigidaire is an OEM part and will fit.