GLEB30M9FBC Frigidaire Microwave Oven Combo - Instructions

This was the first time replacing the fan. It is a lot easier to work in the oven compartment with the oven door removed, only two screws on the door and the hinges were released. I found that a couple of the screws were either rusted or stripped so I used a pair of pliers to remove the screws that were holding the diffuser in place. Once there was access to the fan I found that the fan was warped and that the blades were scraping against the back wall of the oven. The next challenge was to remove the retaining nut. I used a sheet metal screw to secure the warped fan to keep it from spinning. once I figured out that you have to turn the retaining nut to the right to loosen, it came off easily. 1/2" socket with extension. When I replace the fan I used two washers for spacers to make sure that the fan would not scrape the wall of the oven. Its been tested many times and the oven does not make that horrible sound anymore.

Removed electrical connector and two screws. Attached the electrical connector to the new probe and attached with the two screws.

Removed two screws holding broiler element. Released two spring hangers on near the front of the element. Pulled element away from oven and pulled two wire connectors off. Simply reverse process to install new one. Wasn't the problem.

Twisted replacement bulb into place easily. Let there be light!

I removed the sensor from inside the oven with a 1/4” nut driver, pulled the sensor out slowly and then took the connection apart and found out that the connector was different, I cut the connector off of the oven side and then cut the connector off of the new sensor and wired it together. I am still trying to find the ceramic nuts. My oven is working for now. Very easy fix, just wish there were ceramic wire nuts with the new sensor

Your service was OUTSTANDING...Ordered one afternoon, and before lunch time the next day, the delivery man rang my door bell...Thanks a bunch for you excellent service.....

Wife was cooking our thanks giving turkey, when an oder of burning was noticed. I walked over to the oven and smelled the area of oven light, it was bad. I turned off and unpluged oven. Got a screw driver, unscrewed 4 screws then noticed the burned switch from under the oven top. removed 3 wires, covered w/ elec. tape, and pulled oven light switch out front. looked at part number and ordered online. We were able to cook our turkey and enjoyed our meal.

first of all, ordered the right piece, second, brought the right handyman to help...getting the over/microwave out as one piece took some doing...then the cover of the microwave had to come off...once we got to the piece itself, it was no issue... then putting it all back together...took about two hours...he needed our assistance because of thew weight and the need to pull the units out simultaneously

Cut power to your oven in your circuit breaker panel
Take out racks and bottom pan from the oven
Remove 2 screws in element bracket at back of oven
Lift element gently, tilt upward and pull towards you out of insulation
Get the tilted wire connectors clear of the back panel
Remove two wires from from connectors gently with your fingers
Take bad element out of oven
Replace it with new element
Replace everything else
Piece of cake. 20 minutes max: remove old; plug and play.

As this microwave is part of a wall micro/oven combo, we removed the trim, slid out the microwave and tried for days to figure out how to release the microwave control panel. Through sheer force, we were able to release the lower half of the panel...enough to get our fingers, chopsticks and a flashlight inside to remove the broken lever. It took 2 of us to pull the panel out and replace the lever. I was hoping for a video online of how to remove that control panel but luckily we changed out the broken lever and it's back in working order! Glad we didn't have to trash and entire microwave/oven combo for one broken plastic part...it all works fine now.

Husband very ill in bed. It's up to me!! Got a new bulb at HomeDepot and figured out how to get that wire 'thing' back in and the new glass cover installed. I DID IT!! WOW! My husband has always done these jobs around the house.......but now it's up to me.......and I'm not so dumb after all! I DID IT!! Now everyone who comes in the house.....I show them what I DID!! :-)

Simply took oven out of wall, removed back plate, unplugged old sensor, went in the front and unscrewed old sensor, put in new sensor, went in back and plugged in new sensor, put on back plate, push oven in wall. Turn on power

1. Turn off power to the electric oven
2. Removed the two screws in the top side of the oven that hold it into the cabinet.
3. Made a support to set the oven on once you remove it from the wall. Or set it on the floor. You will need help this is not a one person job.
4. Used a Philips head screw drive removed the back of the oven panel. I did not have to remove the whole thing just took out half the screws and the electrical plug for the temperature sensor is right on the edge.
5. Unplugged sensor
6. Took out the two screw on the inside of the oven that holds the thermal sensor in place. Pulled it out the front.
7. Side the new thermal sensor in place replace the screws.
8. Pull the plug out and plug it back in. Check and push the insulation back in place where the thermal sensor.
9. Replace the back and replace the screws.
10. Slide oven back into the wall.
11. Replace the two screws that hold the oven in place in the frame.
12. Turn power back on
Check the temperature

Watched the repair video on your web site. Used the video as a step by step guide in the actual repair.

To determine which switch was bad, I removed all three switches from microwave. I used a D-cell battery taping two pieces of wire to the POS and NEG ends. Tape the POS end of wire to a flashlight bulb's bottom tip. Tape or twist the NEG end to the bottom of the switch. Connect another piece of wire to the top of switch and touch the side of the flashlight bulb with the other end of the wire; the bulb should come on. Depress the red button on the switch and the light should go out. The switch is good if this occurs. If light does not come on or the bulb does not got out once the red button is depressed, the switch is bad. Now you have determined which switch to order for replacement.