Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
leak suddenly developed
Somehow a bobby pin got into the drain pump housing. When it started to drain, the pin was rammed through the housing.Extremely easy to remove and replace. No special skills needed. Whirlpool did a good job in making it idiot proof. Unpacking the part took longer than installing it. Don't be afraid to do this repair. If you own a pair of pliers and a screwdriver,you can do it.
I first had to take off the back and the top to get to the pulley and the belt. The pulley had woobled so much that it had worn out the center nad it would no longer hold to the post in the tub. It also had cut into the back of the tub about a 1/4 to 1/2 inch. I unscrewed the nut holding the pulley and removed it. I then took a knife and trimmed the rough edges off the back of the tub to make it smooth. I then smoothed out the end of the post that the pulley fits on so the new pulley would fit. I tightned the nut and put the belt on the motor drive shaft and Used a robo grip to hold the belt as I turned it onto the pulley. I but the back and top back on and that was it.
This washer had been faulting since it was 1 year old but it only happened 1 to 2 times a year. As the fault problem became more often, I realized it was a hardware or computer malfunction. But what was the problem? Well the problem always was a faulty flow meter. I replace the valve and the flow meter. But I tested the flow meter several times.-- I replaced the flow meter and the valve. And for once in 5 years it did not fault.
Serviceman had previously replaced the hot and cold inlet valves, but the low pressure error persisted. Rather than cough up another $130 for the serviceman to return, plus parts and time, I decided to order the replacement flowmeter from PartSelect.
Unplug power and turn off water. Top of machine comes off by removing three screws at top rear; use socket, spanner or T20 driver. Unplug electric sensor from flowmeter. Old unit is removed, and new one connected to water line by squeezing spring-clips with a pair of flat nose pliers. Reconnect electric sensor.
Great move, easy, and saved myself the thick end of $200.
Detergent leaking under Dispenser Drawer down front of Washer
Secondary problem was bleach being siphoned from dispenser prematurely when drawer slid in. Replaced Drawer, Detergent Container and Bleach Siphon parts. Appears to have been a change in the siphon design when compared to the original factory part. 5 loads completed since replacement of these parts with no premature siphon of bleach or leakage down the front of the washer.
OEM hinge was rusting to the point that it broke on one side
The repair was rather easy. It involved the removal of all the bolts around the glass door and only the bolts on the hinge conected to the washer itself. there was a bit of alignment problem when put back together, minor rubbing, but not much. The door now works close to as good as new.
After removing the Top Cover and back cover by removing the 3 screws for the top and 10 screws on the back cover to expose the interior of the machine. Remove the rubber hose that was attached to the bottom of pressure switch. Pushed gently upward on the pressure switch until it popped out. Gently press down on the 2 small tabs on the plug and then gently pull the plug out. Placed new pressure switch in place, plugged the connector back into the switch. Also doubled checked the hose to ensure that the tubing has not rubbed a hole it from rubbing on the concrete counter balance. If yes then remove the tube from the bottom of the washer and replace with approximately 2 feet of 3/16 inner diameter/1/4 outer diameter tubing. Attach the new tubing to the bottom of the washer port and the pressure switch. Attach the new tub to the water discharge hose using tie wraps or electrical tape to ensure not to occur again.
First and foremost, I usually call a real man to come do a job like this, but after reading the repair stories, I gave it a shot. Very, very easy. Pop of the bottom panel off (three torx screws), drain the water out of the tub (if any), and just follow the directions in the box. Anyone can do this one.
Pretty easy part replacing job. All screws were torx. Pry off plastic molding from front of machine where it covers the hinge with an old thin table knife or something, loosen the plastic molding inside the door, and replace the hinge. Minor hint... put the little round plastic molding back on the round part of the hinge BEFORE you screw the hinge onto the door.
First step was to remove old bellow. I opened the door there is a small wire with a spring attach that holds the outside of the bellow to thw washer. Then removed it from the water inlet, then took a short straight scewdriver to remove the gaint hose clamp holding it to the drum. Installed the new part. When putting hose clamp back on I removed the top of the washer by removing the three screws in the back then I flipped the hose clamp so I could use a long screwdiver from the top side.This will give you alot more room. Hope this helps