GCAM2792TQ0 Whirlpool Washer - Instructions

Found directional gogs broken. Searched washer model # on PS.com and easily found schematic drawing. Received parts in a couple of days. Removed agitator with one nut, and other parts just pulled apart. Replaced the cogs and other parts which were not really broken....just worn. Everything went back together easily, and I was done! Parts Select saved me a LOT of time, and especially money, than if I had called a repair co. THANKS!

Actually this is kinda funny. I ordered the part and it arrived when I was out of town on business. My 20 year old daughter tipped the washer up on its end, and replaced the pump herself in less than 30 minutes. Her only complaint was that no one told her to block the washer up as it almost fell on her.

Remove the nut from the top of the motor shift inside of wsher. then remove the wire harness plug. Take out three bolts side the shaft and motor out. Replace clutch and install in reverse order.

First, I'm glad I found PartSelect. The previous posts for this repair told me exactly how to replace the pump: I unplugged the washer and moved it out away from the wall (did not need to disconnect water hoses). Then I tilted the washer back and propped it up so I could get underneath. Using pliers, slid hose clamps back and disconnected hoses from pump. Using a screwdriver, popped off two clips, top and bottom, that hold the pump in place. Pump then slides right off the shaft. Installation is the reverse. Make sure you align the shaft with the pump. Delivery of my part was FAST - ordered it and got it the next day!

Put clamps on hose end and then used some dishsoap on the inside of the hose to make pushing them into place easier once in place I placed the clamp in correct spot and used a screwdriver to tighten the clamps.

Just turned the washer on its side, popped out the two retainer clips with pliers and screwdriver, pulled the pump out by hand, put the new one in and replaced one rusty clip with the new one from parts select, and used the other old one. I ordered the parts on Monday, and they came tuesday, even with the standard shipping. Also the website parts diagram and whole website design is good.

The repair was very easy. The only hard part was due to the age of the machine the cap covering the agitator assembly was stuck on the top.I had to use a very large pipe wrench to loosen it. Other than that the whole repair went very smooth. You will need an extension with the socket wrench in order to reach the screw holding down the agitator.I was very impressed with the service from Parts Select. I received my part very fast and it included everything I needed to complete the job.

I removed three bolts from the transmission and two clips that hold the motor to the drive gear. I replaced the brake cam that had cracked and the lining. Now it works great ! Ordered part on Friday before two and it came Saturday at four.

Removed the clips. Pulled out the old pump. After trying to get the new pump on the shaft of the motor, I realized that some corrosion had built up on the motor shaft. I got a small tack hammer and very lightly tapped the shaft to remove the corrosion. The pump then slid on the shaft with no problem. Replaced clips. Job complete.
The corrosion on the shaft cracked the plastic piece where the shaft connects and this is what caused the problem in the first place.

1. unplug washer
2. move washer out from wall.
3. remove 4 screws that hold control panel; 2 screws on face and 2 screws an back
4. lift control panel to reach plug for lid switch
and unplug old switch
5. open lid and remove 2 screws that hold lid switch on top opening; remove nut that holds ground wire from lid switch
6. remove old lid switch
7. new lid switch needs to be modified to fit in position,i.e. break tube surrounding wires of lid switch to be 1/2 length.
8. plug in new switch at control panel
9. screw in lid switch at lid opening and reattach ground wire.
10. screw control panel in place

flip machine back remove two spring clamps and hoses remove two spring clamps and water pump save $500.+on a new washer

First I removed the softener bin by pulling it up and off, then I removed the plastic seal by pulling it up and out, then I removed the 1/2 inch bolt with a ratchet and extension, then I removed the upper and lower agitator assembly from the machine and seperated the two by putting my feet on the lower agitator to hold it to the floor and pulling the upper agitator fast and firmly.
Sitting on top of the lower agitator I found the dog ear assembly. I pulled the dog ear assembly off and removed the yellow cap and existing dog ears.
Assembly was reverse.

Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towards me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order

I pulled back off machine. A real pain. Not something you have to do although once the back is off, the whole cabinet just lifts off. Idealy: Remove agitator and reatiner clip, lay washer on it's side or face, Remove electrical connector form motor, remove two hoses from pump, (motor can be remove easily from transmission if desired. It's lighter), remove three 1/2" bolts, lift transmission w/clutch assembly out. Pay attention to orientation of flat washer and clip (remove). The cluch band is indside the silver cover. Pich together with pliers to relieve tension and lift out. There are three while pads that wear away and glaze over when they get too hot from slipping. Reassemble. Ths is from memory so I hope I didn't forget anything. Time to do it this way would probably only be 45 minutes.

I didn't think this would be particularly difficult but it was easier than I expected.

UNPLUG THE MACHINE

Remove the two screws (one on the right , one on the left) That allows the control panel to swing up.

Lift the panel up.
There is a plastic wiring connector that is secured in the top of the washer housing. Press the sides of the top of the connector and remove the top connector. (The bottom part of the connector will still be secured to the housing)

There will be two clamps one on the right side under the control panel, and one on the right.
Use a screwdriver to pop out these clamps. This is where I used the washcloth to place between the screwdriver and the washing machine body to avoid scratching the surface.

Once you pop out these clamps, the housing is free from the tub frame.
Twist the housing just a little and tilt it forward. IT will just slide off the frame.
You can now take the housing wherever you want to more easily get to the switch. It is mounted in the housing.
Take a good look at the way the switch is mounted and the wiring tube is secured because you will need to at least have an idea how to put it back into place.

There will be two clips that hold the wiring tube in place. One on the side and one on the top. Use a screwdriver (and the washcloth if necessary) to loosen and remove the clips.

There are two screws that hold the switch to the housing. Remove these and keep the screws. You will need them to attach the new switch.

Now the only thing keeping you from removing the switch is the connector which you saw earlier before removing the housing. Squeeze the sides of the clip and free it from the housing.

Mount the new switch into the housing and route the wiring. You may have to use a small pair of pliers to squeeze the clips back together to hold the wiring tube to the housing.
Attach the green ground wire to the housing frame just like the one you removed to get the wring tube off the housing.

Push the connector end through the hole designed for it until it snaps into place.

Replacing the Housing back on the frame:
Let the housing all the way down, and slide the front lip of the housing UNDER the front brace of the tub frame.
Carefully let the housing lower onto the side rails (the housing will go on TOP of the side rails).
You may have to gently twist the housing to let it fall into the proper place.
Take the clips and secure the housing back to the tub frame.
These just POP back into place with applied pressure.
Re-connect the lid switch to the control panel wiring connector.
Swing the control panel back down into place and replace the screws on the left and right sides.

PLUG IN THE MACHINE

Viola!! You are ready to perform your favorite laundry task.(Yeah RIGHT!!) Or just yell "HONEY the washing machine is ready for you." Anyway, after the swelling in your eyes go down you will see that your washer is ready to use.

This took me about 40 minutes but some of that time was spent understanding just what to do. With these instructions, you may be able to do it in 30 minutes.

I hope this helps you. Kudos to the Whirlpool Engineers who made this machine easy to work on. This is the 3rd repair I have done on mine. (Rebuilt the agitator drive and replaced the timer) For 18 years of use.. that ain't bad. I think it is good for another 5 years at least. Total cost for this repair: Part=$37, Shipping=$7, Time spent=40 minutes. Not bad considering a serviceman is going to charge $90 labor for the first hour plus parts.