Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice stuck in mold. mold coating was peeling off.
Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.) I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold) circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end) Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.
Old motor was not resetting back to proper position halting ice production.
Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!
First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.
This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.
Heating element broke and fried the rest of the parts had to take out the bad parts and put in the new ones and it worked. i have fixed this problem three times now.
Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one. But Parts Select is a great place to order from. Thank you.
Remove the unit cover by unsnapping from the bottom. Remove the face plate on the switches. The ice door simply snaps off the closing mechanism. The problem I have is that the original door included a heat trace element (keeps the back of the door warm to limit condensation). The new part was simply a new seal. I clipped the leads to the het trace (turn off the fridge before you do that) and put in the new door. When the heat ids on in the house there is no problem with condensation but on warmer days its pretty bad. I cannot find a replacement part with the heating element and have contacted Whirpool. THey haven't responded as of yet.
Ice Door broken letting warm air into Ice Maker system which kept freezing up.
I didn't have to buy a new Ice door kit. The part on the Refrig. door I needed I found out was unavailable. The door parts (Ice door parts and the asembly for the water unit) screws into that part. I found out that I would have to replace the whole refrig. door which was $900.00. I took every apart got me some pvc glue used it on the door and bought the original screw online with some other assorted parts,Door switch, etc. and was able to repair in about an hour. Some of the parts are very fraigle so you have to be very careful or you will be buying some new replacement parts.The new nickel and dime parts are expensive. My Icemaker was leaking where the Ice was clumping together in the bin, and when I checked the unit was $125.00. I found a new one and replaced it for about half that price. I am now very happy! (a least until the next project.)
I unplugged the refrigerator Opened the freezer door Opened the ice maker door so that I could easily get to the emitter and receiver I used a phillips head screw driver to remove 3 screws from the emitter plate and 3 screws from the receiver plate I unplugged the faulty circuit boards--this took some tugging I firmly plugged in the new circuit boards and replaced the screws I waited about 30 minutes and the ice maker began making ice again
Ordered the parts from Parts Select and had them within two days (lightning fast shipment--and with just standard shipping). Disconnected the power to refrigerator, removed three screws from each cover panel, pulled the panels loose from the freezer wall, disconnected the wiring harness on each, removed the screws holding the two boards, replaced the boards with the new ones, attached boards to cover panel with screw, reconnected wiring harnesses, replaced the three screws on each side, restored power, and made ice! Whole job took about 15 minutes.
After receiving the replacement emitter and receiver boards from PartSelect.com, I following the troubleshooting paperwork that came with my order to ensure the parts I ordered where the problem. After which, it was very straight forward: unplug the frig, unscrew the 3 screws on the covers for each board, unplug the push-pin connection, remove the board screw, set the new board in, and plug back into the connection. It took approximately 20min.
Unscrew the three phillips screws holding the flipper and electric eye unit, pull it out a bit to unplug the connector. Take the assembly over to a flat surface, and use pliers and or crew driver to pry/pull off the press-on retainer on the hinge pin. Pull out hinge pin, remove the broken flipper. Put new flipper in place making sure spring is behind the flipper (holding it open). Reinsert hinge pin, and then reuse the press-on retainer to hold in in place. Then take the repaired assembly back to the freezer, re-plug the plug, and then reinstall the unit using the 3 phillips screws. Easy Peasy.
