EER3000H02TW General Electric Range - Instructions

recieved part the next day. looked different but I followed instructions and the part worked perfect.

My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, and they look great. The price is less than any other site I investigated.

I pulled out the range from the wall unplugged it from the wall then i opened the oven door and removed the two small screws on the front off the range and lifted the glass top and supported it with a 1/2" X 18inc wooden dowel, then i removed the two burner retaining screws with a small Phillips screw driver and removed the wires from the burner,
then i replaced the burner with the new one and reconnected the wires and placed the burner in to the two retaining clips and then tightened the two screws then i removed the wooden dowel and installed the two screws on the front bottom side on the range then i plugged in the range in and tested the burner then put the range back against the wall.

Simply pulled old gasket from door and pushed new gasket clips into existing holes and tucked in ends at bottom of door.

Turne off power to range..pulled oven out..Took top back panel off with nut driver. 4screws .. Took picture of control board....removed bad control board with Phillips driver...4 screws....installed New board...removed 1 connection at a time and replaced in New board..Turned power on to test new board...check picture to make sure connections are correct...turn off power...put back panel back on...put range back in place...turn power back o n...done ..approximate time 15 to 20 minutes..

Unplug stove.
Remove rear panel of stove with a nut driver or socket. Remove knob from switch and use small screwdriver to remove screws on front panel switch. Remove and replace each wire contact one at a time to ensure correct wiring configuration. Replace screws on front panel to secure switch. Plug stove in and check that it works properly. Replace rear panel and move stove back in place.

replaced lights in refrigirator and freezer

Troubleshot the problem, found the SWITCH ROCKER was seized up,
Removed the rear inspection panel, and saw the installation procedure.
Called Part Select and discussed the problem.
Gentleman quickly found the part and we ordered it,
Pulled the existing failed switch out, replace the new switch, done.
Saved at least $100.00 by not having and appliance company do a simple job!
This not the first time Parts Select has satisfied my needs and importance of saving hard earned money.

Sincerely
Satisfied customer
Edward P. Mike

I went online and ordered the part after reading other people's repair experiences, confident that I could do it because the part was quite pricey. First, be sure you're circuit breaker to your range is off. Next, open the oven door and locate and remove two screws with a socket, that are just under the top surface which will allow you to lift up the glass top which is actually hinged...no need to pull the range out. Securely prop up the glass surface area and the burners are exposed. With a marker, mark where each color wire goes on the burner you are going to remove and also mark where the two holding brackets are. This way you can reference the locations to connect to the new one. Carefully remove the wires and brackets and install new burner with brackets and connections. Close up the top, replace two screws, turn on breaker, and if there were no other faulty components,it'll work great. P.S Be gentle getting the very snug wires off. Good Luck

Read the instructions on how to remove the door, found in the owners manual. Once you release the hinge lock latches, the door can be lifted off of the hinge arms.

It is fairly heavy and bulky. I spread a large towel on the kitchen table and placed the door, front side down on the towel.

Remove the 3 nut screws at the bottom of the door and then lift the inner door assembly up about 3" and hold it up temporarily with a medium sized plastic food storage container. This will allow room to access the 4 nut screws (2 on each side) that secure the trim to the door.

The old trim was somewhat difficult to remove because of years of rust and other build up where the front door glass goes behind the trim. Be careful not to damage the glass. I used a putty knife.

The edge of the glass will be soiled so I used a mild abrasive cleaner to remove the rust and grime, and then used a window cleaning spray to clean the glass.

The new piece had to be "fitted" slightly to match the existing screw nut holes but it goes together quickly.

I am a 69 year old woman. I watched the Repair Clinic YouTube Video before I started. I then pulled stove away from wall and unplugged it. Took off oven door and removed the top oven rack. Loosened and removed the screw holding the temperature sensor located inside at the top center back wall of the oven. Pulled the sensor through the opening until the plastic plug came through. Unplugged and removed it and plugged in the new sensor. Fished it back through the opening. Replaced the bracket to the back wall of the oven and tightened the screw. Replaced the oven rack and stove door. Plugged it back in and moved it back into place. I turned on the oven and let is heat for over 30 minutes and the internal temperature was correct with the setting.

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. Connected the wires and resecured top to base. Turned on the current and it worked beautifully.

Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !

Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la estufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.