ED2KVEXVQ01 Whirlpool Refrigerator - Instructions

I followed the UTube video step by step, pausing at each section made repair very easy. Watching the video is a definite must!

snapped in new bins.

Replaced the water inlet valve. Note: although the web site shows the exact same water inlet valve, the replacement is somewhat different. You'll notice the electric prongs are facing in the opposite direction then the old one. It works like a charm need not worry as I did when I saw that. The old part is actually two parts in one. Use care when separating the front piece (it acts like a coupling where the water supply connects to and simply comes out the other side and into the refrig.) from the water inlet valve. It was a tight fit coupling that front piece to the new valve but it will fit. Make certain you purge 1-2 gallons of water before consuming any. Also dump a tray or two of ice cubes.

Exactly how the instructional video described it to be. No surprises what so ever. Ended up not being the culprit to my problem. Ordered and installed a bi-metal defrost timer. Also, extremely easy as the instructional video described it to be. Partselect is an awesome resource for knowledge and quality products with very reasonable prices.

Shut off Water and Electricity. Took out the Ice Bin. Removed one bottom hex nut and then loosened top-side hex nuts (don't remove them, just loosen them) the Ice maker will slide onto the hex nuts on the side of the refrigerator.Disconnected the wiring harness from the maker. Put everything back in reverse order and Bingo! No leaks and lots of Ice.

Easy repair, just snapped the old bins out and put the new ones in. It took longer to empty the old bins and fill the new ones. Customer service was excellent, also my order was to me in 2 days. Great service. Thanks PartSelect

unplug refrigerator, take backing off with nut driver. Pull old blade off and put new blade on. Put backing back on and plug in.

I looked at the video that part select send. I did exactly what it said to do,and now my refrigerator is working just great. And the noise is gone. I thank you so much for your help. And I'm a 64 year old women thats how easy it was.

1. Cleared all the food items off the broken shelf. 2. Removed the old shelf. 3. Removed the new shelf from the shipping box. 4. Inserted the new shelf. 5. Replaced food items.

It was wonderful. I struggled with the old ones taping them and repairing them until it just didn't work anymore. Within two days they were here and problem solved. What a relief.

1. Remove the ice-maker/water dispenser cover plate located on the freezer door, by: inserting a putty knife blade at the bottom and freeing up the two retainer tabs; then pushing up. (note: be careful pulling the cover plate, there are many electrical connections on the back).

2. Note the electrical connections on the back of the cover plate and locate the connect close to the inside of the freezer door and disconnect it. (Note: this is much easier than pulling each wire off its connection point and then having to remember which color coded wire went where).

3. Carefully work the door hinge pin back out to the right and remove it and the hinge (Note: in my case the pin was already half way out so the old door couldn't close - and since this model door had a heater which came on because the door was misaligned there was constant flow of warm upwards causing ice to melt, run down and re freeze thus making the door difficult to open).

4. Unscrew the single her head screw holding the small metal piece to the right that retains the know upon which the outer door frame turns. Move the frame to the right to free it and work it out if the way. You now have access to the ice-maker door and hinge pin assy.

Unscrewed one screw under icemaker and the two screws above, pulled out old icemaker unhooked power cord attached cord to new icemaker replaced screws and attached bail wire from old to new pluged in the refrigerator and icemaker started making ice, took about 30 minutes before first ice dropped into ice holder.

I can tell you they had the tray to my house within 3 days!! AM I IMPRESSED! Also they were a lot cheaper than ordering the same part from the major store where I bought the fridge. Thanks!

My husband and I followed the instructional video on how to replace the "direct drive drum". We took note of how everything looked prior to dismantling the ice bin. We made sure we had the proper tools and a large flat surface to work on and started taking out the screws. Replaced the new drive drum part and put it all back together. The whole process took approximately 30 minutes and the ice crusher works great now. I'm a happy camper!!

Ordered a new shelf. Removed the old one and installed the new one. Wife is happy. :-)