Models > E23CS78GPS0 > Instructions

E23CS78GPS0 Electrolux Refrigerator - Instructions

All Instructions for the E23CS78GPS0
346 - 360 of 409
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Freezer side kept defrosting
After receiving the parts, I clamped on the connector ends, and put on the shrink tubes. Unplug frig, took out the shelves (4) screws, unscrewed back panel (4) screws. Took old thermostat off tube, clipped (2)wires on old thermostat, splice wires, clamped connector on old wires, moved up shrink tubes, and used a heat gun to shrink the wires. Put new thermostat on the tube the old one came off of, put panel, and the shelves back. Pugged frig in. Works great!
Parts Used:
Defrost Thermostat Kit
  • Greg from Camarillo, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
our crisper cracked
just insert the new crisper 1-2-3 done!
Parts Used:
Refrigerator Crisper Drawer
  • Barrie from cleveland, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
water to ice maker
electrical unplugged. water turned off and disconnected. cardborad backing off (4 screws). removed part (2 screws). unplugged electrical connections. removed each line one at a time and inserted into new part, connected electrical connections. placed new part with all connections back onto refrigerator, (2 screws), backing back on, water line connected, and electrical connected. no leaks with new part. simple uninstall and install for do-it-yourselfer. instructions need to be printed in larger font for easier reading.
Parts Used:
Refrigerator Water Inlet Valve Water Tube
  • dennis from reserve, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Fresh food door popping when opened.
Followed instructions on removal of door, replaced bottom plastic bearings. Lubed with some grease. Viola! (Actually was just the hinge bearing that was broken, so could have saved 6.00 but I figured why risk it and replaced them both.)
Parts Used:
Door Closing Cam Hinge Bearing
  • Michael from Kensington, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
popping sound in door
Took door of and replaced bearing Two screws . HARDEST PART WAS TAKING FOOD OUT OF DOOR.
Parts Used:
Hinge Bearing
  • Douglas from Marlborough, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Clicking sound at hinge bearing whenever door opened
Removed everything from inside door. Loosened top plate screw, lifted off top of refrigerator. Lifted door up and onto the floor on its side. Removed old hinge bearing. Inserted new hinge nearing. Applied grease over hinge bearing surface (very important step). Replaced door, replaced top plate. Replaced all items on door. Clicking sound is completely gone.
Parts Used:
Hinge Bearing Upper Hinge Bearing
  • Richard from Rockford, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Crisper Support Broke Off
I tapped in the peg like it showed in video and pried out with flat screw driver and hammered other peg in flush with part
Parts Used:
Crisper Support - Rear
  • Denise from Claremore, OK
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
not working due to ice on coils
unplugged frig, removed shelves & inner lower back panel in freezer side, removed defrost thermostat from tube, cut the wires and spliced in new stat wires with provided wire splices crimped together and replaced thermostat on tube it has been a week and no ice so far??. this was after 2 trips by the repairman who replace the defrost timer board which was most likely good at a total of $160!!! still cheaper than $1000 for a new frig!!!!!!!!!!!!!!
Parts Used:
Defrost Thermostat Kit
  • terry from litchfield, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The ice crusher flap was broken.
Took out the ice box, dumped the ice. Let warm up a bit. Then took out the housing and installed the new one. Works great. Saved a lot of money! Only took a couple days to receive the part. Great service.
Parts Used:
Dispenser Crusher Housing
  • Mary from Allegany, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
ice maker didn't work
replaced with kit, very easy unplug unsrew and replace, any one can do it
Parts Used:
Rear-Mount Ice Maker Assembly
  • louise from acampo, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
misplaced
When my wife and kids moved down they lost the upper bracket and the screw for the lower cam. parts show up and matched perfectly to the orginal no issues at all
Parts Used:
SCREW-#10-32 X 3/8 Upper Hinge Bracket
  • michael from covington, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
My Ice Maker stopped making ice and the water dripped from the dispenser
I turned off the water, removed the cardboard cover from the back of the refrigerator; removed the 2 screws holding the water valve in place; unscrewed the plastic tubing from the valve; unplugged the wires to each solenoid (3); the old valve had threaded connections for the plastic water lines, the new valve didn't; I had to cut the ferrel off of the plastic lines so I could insert them into the new valve and then press the connector into the valve (I didn't anticipate something like this, but it worked fine); I reconnected the wiring and screwed the valve back into place. The ice maker started making ice and the water stopped dripping from the dispenser. The best $65 I've ever spent.
Parts Used:
Refrigerator Water Inlet Valve
  • Raymond from Sinking Spring, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Plastic bearing broken on bottom door socket
Simply removed old bearing with the pliers and aligned new beating into the socket.
Parts Used:
Hinge Bearing
  • Eric from Brick, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Ice would not release
To describe this replacement as "really easy" is an understatement! The hardest part was digging the socket set out of the tool box. The instructions were well written, as were descriptions of fellow home do it yourself types. Those gave me the confidence to just for it. I am so tickled with myself and the money I saved! My hubby is pretty impressed too! Cathy
Parts Used:
Rear-Mount Ice Maker Assembly
  • cathy from Columbus, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
The Door Closing Cam had crumbled
followed the video and had little or no trouble loosening or tightening bolts or phillips head screws. The only difficulty was removing the spacer on the door itself. Otherwise a piece of cake. Good video and easy to follow instructions.
Parts Used:
Door Closing Cam
  • Vann from Kennesaw, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the E23CS78GPS0
346 - 360 of 409