E23CS75DSS9 Electrolux Refrigerator - Instructions

Took all food out of the refrigerator door. Pulled the door off by unscrewing the 3/8 hex-head screws on top and bottom hinges. The door is relatively light and removes very easy. Unscrewed and removed the broken plastic cam pieces and replaced with the new ones. Replaced the steel hinge, even though it was still in good shape. The hinge kit comes with left and right hinges as well as a spare cam insert with each hinge, so I still have all the left side parts and spare cam insert for the right side for a future fix if needed. The repair itself was extremely easy and took about 10 minutes; the total time that included emptying the food, cleaning the bottom grill plate and replacing the food was about 20 minutes of my evening.

Remove door,remove hinge,replace hinge,replace door. Very easy.

removed 3 screws on top hinge plate. removed door and replaced hing bearing. reinstaled door.

Pull out the old clips,that were crack.The new ones are hanging off.I don'nt know if i should put some kind of glue,or something.To help it stick on.

I spent most of the time pulling the frog out of the enclosed space. Tow bolts at the rear of the unit, took off with a socket with a long extension, disconnected the interface and then reverse--Very easy

Simple: Loosened 2 screws/bolts holding icemaker in place; removed old icemaker; disconnected old wiring harness; connected new wiring harness; replaced new icemaker; tightened 2 screws bolts; turned new icemker on. Time: less than 5 minutes. It took me longer to order the icemaker. Then I had to find my socket set.

Replaced ice maker

So easy a cavewoman could do it!

took ice maker out empty ice removed 6 screws removed auger out took off lcck nut pulled off drum replaced with new drum reassembled.

I diagnosed the problem by checking the water flow at the supply valve and hose by disconnecting the hose from the back of the fridge. Found the pressure to be adequate. I then reconnected the supply hose and removed the cardboard backing from the fridge and removed the nuts holding the water inlet valve to the chassis. I loosened the first hose that runs from the bottom of the valve and had my wife activate the valve by pushing the water switch on the front of the fridge. Water basically sputtered out of the valve and I decided that was where the problem was. I ordered the valve from partselect. When it arrived I thought it was the wrong part because it had push-fittings whereas my original valve was all thumb screws. I took a chance and one by one used a utility knife to cut the hose free of the old valve as close to the nut as possible. Connecting them to the new valve was a piece of cake! Just make sure the hose bottoms out when you push it in. I turned the water back on, no leaks! Plugged the fridge in and pushed it back to the wall. After a bit of air bled out I had a strong flow of wateragain like new! The next day the ice cubes were solid again! We use the filtered water so many times a day and had been so frustrated with the slow water flow we had considered donating the fridge and buying a new one; thanks to this easy fix we expect keep it for years to come!

I followed a video I found on how to take the front off of the ice dispenser ( to me the hardest part) Once I was in there it was a matter of removing the pin and spring,then putting the new flapper in place of the old. Hardest part in reassembling was getting the spring back where it belongs. After that it was a matter of putting the ice dispenser back together and testing. Works perfectly.

Remove 4 screws to get the housing cover off. Remove the lock ring that holds the ice auger in place. REmove 4 screws to get the crusher housing off. Reverse the order to replace the housing. Very simple.

Pulled fridge away from wall and unplugged. Turned off main water supply feed and removed fitting from water inlet valve. Took off back panel by removing 3 screws. Took out 2 screws holding valve to fridge. Pulled off color coded wire clips. Unscrewed each water tube connector. New valve had quick connectors so had to snip off flared ends of tubing with utility knife. Pushed tubing firmly into new valve fittings and pulled to ensure connection. Reattached wiring and reattached valve to fridge with the 2 screws. Reconnected water feed line and turned on main water feed. Checked for leaks before replacing back panel. Done. No more dripping from water dispenser.

It went okay. My husband did the job and he is handy. We both watched the little "How to" video and that was very helpful.

Had to pry the old one from the cabinet. Had to work remaining piece evenly as to not crack the cabinet of the fridge. Not the best design on Frigidaire's part but it was fixable. Thanks for stocking every part under the sun.