DU4500V Magic Chef Dishwasher - Instructions

I had to take the complete builtin dishwasher out of the base cabinet in the kitchen.

turn off electricity - circuit box
turn of water supply - turncock under sink
remove kickplate - screw driver
disconnect electric wires - screw driver
disconnect water feed - 5/8 wrench
remove top screws at counter underside - screw driver
pull out dishwasher - hands and son
turn dishwasher upside down - hands and son
got some water on floor - towel to mop up
remove top shower hose ( a rigid pipe with a screw fitting at top and a neoprene coupler at bottom) - hands
The neoprene coupler is the part that failed, it had worn thin due to heavy water flow

reverse process - same tools

voila - no water leak

I replaced a Silverware basket at the same time, which took two mintues as I had to remove the handle from the old basket and press fit onto new one - hands

Parts Select had the parts I needed and delivered in less than 48 hours. That is great service.

no problems, very easy

I went to take the bottom front panel off and ended up dropping the screw down behind the baseboard and then found that I did not need to take the panel off. The broken end of the float was not obstructing and I was able to just drop the new float in place. I spent more time looking for a replacement screw than any thing else. Ran it and it works fine.

Removed old gasket and simply replaced it with the new one. Very easy.

The dishwasher was running perfectly, but over time it leaked more and more. We were ready to throw it out, when I searched the internet and saw stories about a tiny gasket commonly failing. I couldn't believe that could be the trouble, but ordered the $3.75 part. Unscrewed the door, slipped out the old gasket and slipped on the new one. Screwed the door back. And the result? THE LEAK IS FIXED! Unbelievable. The old gasket had gotten stiff, probably exposure to soap, and it wasn't sealing properly. That $3.75 part saved us hundreds and hundreds of dollars and will give us extra years of use from our dishwasher.

removed old nut and arm, put in new one, took about ten seconds

pulled out the old gasket, cleaned the area before pressing in the new gasket with my fingers ,I made sure to put it in the same way as the old one. You have no idea how happy I am that this solved the problem.

I removed the original gasket, wiped down the area, and installed the new gasket the same way the old one was installed. It was very easy.

removed old deteriorated gasket - just pulled out
cleaned soap particles from door seal area
pressd in new gasket - note orientation
done.

still leaks - will investigate further

My husband thinks I'm the smartest wife ever! He's telling all his friends how I got online to research the problem (thanks to your readers and DIY comments!), diagnosed it, ordered the parts and - voila - clean dishes once again! It's like everyone said, remove inside of the door by removing 7 torx screws, dismantle wiring -remember to note what connects to what - pop out old parts, easily insert new ones (that arrived in record time!), reconnect wiring, replace door and you're done. Replacing the reservoir o-ring also stopped the leaking problem that preceded the door issue. Thanks PartSelect!

After pulling dishwasher out both springs easily installed using plastic connectors on the bottom left and right sides. Pliars were used to stretch the springs. It took fifteen minutes at most.

just unscrew the inside panel. using a torx screw driver. disconect vericarefully the bad actuator and install a new one. put back everything in back order .

romoved 3 screws, removed spray arm support nut. pulled off spray arm support, replaced new spray arm support and spray arm support nut

Popped off the plactic screen filter (3 screws). Droped in the new Spary Arm and put back together.

You guys are AWESOME! I ordered the part on a Wednesday afternoon and received it Thursday morning. So all and all I didn't even have to wash any dishes by hand.

I pulled out the old gasket and put in the new one. You need to stretch it a bit as you guide it in the track.
It was very easy but did not solve the problem.
Apparently, Maytag dishwashers are known for a leaky soap dish which I figured out after the door gasket was replaced. The problem is usually with the soap dish latch. You need to take the inner door off, disassemble the soap diehs, out a new gasket and latch on, reassemble, and you should be all set.