DU1055XTSS2 Whirlpool Dishwasher - Instructions

twist filler hose assembly to the side and slide hose in. place clamps on hose and attach to water supply and valve.

Turned off water to dishwasher and disconnected hot water and drain hoses. Removed to side screws and kick panel and pulled dishwasher from under counter. Removed old drain hose and fed the new one over to the drain. Reconnected the hot water and new drain hose. Pushed dishwasher under cabinet and screwed to cabinets. Ran the dishwasher and checked for leaks. Replaced kick panel.

removed the front panel of the diswaher. unplugged the soleniod. removed the old detergent dispenser cartridge. replaced with new detergent dispenser. plugged in the soleniod. replaced front cover. ran a cycle to make sure the despenser door worked.

I removed old hose and replaced it with a new one and reinstalled the dishwasher.

i found this website,and it told me that 60% of the time it was the bimetalfuse. i watched the vido to see how to install it, pretty easy,so i ordor the part. Two days later my dishwasher was up and running. thank you partselect,you saved me a hole lot of money. yours truly marc

Turned off the circuit breaker to the dishwasher. Removed the screws inside the door to open the control panel. Located the thermal fuse. Removed the wires from the thermal fuse. Using a multimeter verified the thermal fuse was open. Ordered the replacement part from part select. Order was placed on a Saturday evening. Part was at my door on Wednesday morning. Using the previous method to access the control panel, I removed the thermal fuse and replaced it with the one received. I choose to replace just the thermal fuse and not cut the wire and splice in the new wire that came in the package. Replaced the control panel, tightened the screws. Dishwasher has worked great ever since! The actual replacement of the thermal fuse took less than 15 minutes. I'd hate to think what a service call and repair would have cost me compared to doing the repair myself.

shut power at breaker. removed control panel and fuse. cut the wires close to the fuse. installed wires in connector. put panel back on. turned on power. hit the cancel button, the water drained. dishwasher back in action.

I checked on line and found evidence that my problem most likely was the failure of the circulation Pump Motor. I ordered the motor from Parts Select. When it arrived, a small section of the housing was damaged. I called for a replacement. The customer service agent was very helpful and the replacement arrived in less than 24 hours. I followed the video provided on YouTube http://www.youtube.com/watch?v=LjRxJy2IUE8 and the one on PartSelect. Both videos helps provide greater clarity for the whole job. The hardest part of the replacement was disconnecting and reconnecting the water supply line. These were my steps. 1. I turned off the electrical power and water supply. 2. I removed the screws holding the dishwasher to the counter top. 3. I removed the two screws holding the bottom access panel. 4. I moved the dishwasher out about one foot and disconnected the water supply line. (Fortunately I didn't have to disconnect the power supply and drain hose because there was enough slack in these lines.) 5. I moved the dishwasher all the way out from the counter and moved it over on the its side. 6. I removed the bolt holding the motor and the motor shield. 7. I removed the connector supplying power to the motor and removed the motor. 8. I removed the inside screen, cleaned and replaced it. I also wiped the other surfaced with a clean rag to ensure a proper seal for the motor. 9. I also applied vasaline to the rubber grommet on the motor to ensure against leaks. 9. I aligned the arrows on the new motor housing and impeller housing and installed the motor as shown in the videos. 10. I reinstalled the motor shield and retaining bolt. 11. I reconnected the water supply, stood the dishwasher upright, turned on the water supply and found I needed to tighten the water supply connection a little more to stop a minor leak. 12. I ran the dishwasher through a rinse cycle to ensure it worked properly and that there were no leaks around the newly installed motor. 13. I reinstalled the dishwasher under the counter top, reinstalled the screws holding it to the counter top and replaced the lower access panel. While this took me a few hours, it was well worth the effort because a repair person wanted $500 to do the job. Thus, I saved well over $300 after paying for the motor. Good Luck with your repair job.

To adequately access the drain motor pulling the dishwasher out was required which was the hardest part. Once the dishwasher was out and laid on the back, replacing the motor took about one minute(Very easy, one clip and a small electrical plug)

Found your website ordered part and received it in 3 days. Took less than 15 minutes to install. Will keep your website handy. Thanks.

I did the repair on the Whirlpool Dishwasher(Quiet Partner II) as shown on the instruction video. With this particular unit you may only have to remove the top 6 screws. The video was excellent in directions. Hardest part to me was shaving the wires, i mistakenly cut them when removing the outer covering. But was a little worried after completed because it cut off again after i first turned it on. But did a second time and it actually completed a wash. And have been working fine for past 13 days. So far so good. Just for someone to look at it and fix was going to cost me $269. I completed job myself for 30something dollars with expedited shipping. So you do the math... Thanks Part Select. Love the website set up.

I unfortunatly removed the whole base assembly to replace this motor. I wasn't sure what the original cause was. After watching your video I would have followed it and it would have been easier. All went well with not leaks and now we can sleep with the dishwasher on. Thanks

Removed the dishwasher from under the counter, disconnected the copper water tubing, placed it upside down, removed the old pump and replaced with new. The only iffy situation is making sure the copper tubing doesn't kink when removing the dishwasher and putting it back into the cabinet. Very simple, my husband can fix anything. Your video was very helpful as well.

very easy

I noticed the top spinner in the top tray. It wouldn't stay when I tried to reattach it. I searched around the Internet using the model number of my dishwasher. I ordered the part which arrived in two days. I removed the top tray and gently pried the piece where the spinner attaches away, took the old pin out, snuck the new pin in there and snapped the spinner in. The problem was that the nipple on the pin was worn away. The spinner was fine but I didn't see an option to just buy the pin. The I st ructions I read said to dismantle the whole works, but I sneaked it in without doing any harm. I hope. Dishwasher works fine.