DU1055XTSS2 Whirlpool Dishwasher - Instructions

First checked my house cb's. Then visited this site and found in troubleshooting guide that the problem was 6x% likely the thermal fuse; location was shown on parts guide. Used my multimeter to verify that fuse was open. Order new one from your site. Installed after receipt and all is well. Most difficult part was getting the door panels in position to reinstall sheetmetal screws. Hope this helps.

Removed the old gasket by hand by pulling on the end of the gasket and slowly removing the gasket. Wipe the are with a clean damp rag to remove any soap or debris buildup. Follow the instruction that accompany the gasket, slowly insert the gasket and do not stretch the gasket as you push by hand into the slot. Run the dishwasher with a rag at the bottom. I had to run it twice, I believe the gasket has to relax and seal the door from leaking. GOOD LUCK, you probably saved yourself a lot of money in service repairs costs.

fold in half, start in middle of door, and press into place with fingernails and work around the door frame

Removed access cover off very bottom of unit with nut driver. Located water intel valve. Placed hand towel under partvto be removed. Then remove water inlet valve with nut driver part is held on to unit with one nut head screw. With plires removed wire attached to water inlet valve. Then used wrench to remove water line and pliers to remove fill line. Reinstalled new water inlet valve opposite of way removed it. I am a 36 year old woman ifbI can do it so can you!

I simply followed the instructions on Youtube video. They couldn't have made it any easier.

Easy to replace this drain hose, but being the section that attaches to the pump, the dishwasher had to be removed from under the counter. Most of the time spent was disconnecting the supply, drain and electric then removing the dishwasher. Once out, the drain hose replacement should take 5 minutes or less. Very straightforward. Please remember to shut off electricity and water supply to the dishwasher before starting this project!

we stretched the gasket and reused the old part. then we ordered a new dishwasher

Unsnapped the old clip and snapped the new one on. Inserted the steel bar into the plastic clip and we were done. Great thank you saved $80 on a service call.

Just screwed it on. Really impressed with fast service getting it to me.

I replaced the door gasket. This was easily done. First I removed the old gasket by simply pulling it out, no tools needed. The gasket is simply resting in a slot. Then I installed the new gasket by pushing it into the same slot, after I had thoroughly cleaned it with vinegar. I did not need to trim the gasket at all; it fit perfectly.

My son Eric, read the directions and followed every instruction. Job was complete in less than 15 min. I filled dishwasher and set it to clean. Worked perfect and dishes came out sparkling. Thank you for you service. My ordered part was here overnight and instructions were easy and clear. Rebecca

Start by removing the dishwasher from cabinet. Oh, don't forget to turn off water supply and also don't forget to install a plug on garbage disposer so when your other half uses the sink while you are outside you don't end up with a leak! Both supplied hoses installed easily, the third which I used semi flexible clear tubing with clamps deemed more difficult to bend, so I soaked the hose in very hot water to make it more pliable thus making the bends easily. I then had to wait until I was sure I captured the culprit before re-installing the unit.Your sales person was very informative and knowledgable and helped immensely!

The Parts select video instructions for this part are pretty much spot on. The grinder assembly broke where it attached to the circulator pump impeller shaft. The screen became totally clogged and thus no water pressure to the diswasher spray arms. The only thing Id add would be to verify the circulator pump impeller is in good shape after removing the old grinder assembly and that you are able to rotate it by hand in case the impeller motor itself is seized or the impeller is jammed. Once the grinder assy was replaced good water pressure and cleans like a champ.

Many thanks for the repair instructions. My dishwasher has a black plastic cover over the control board but it was easily removed. I did take a photo of the board before I started to use as a reference in putting thing back correctly. Being 70 and never having done anything of this type I was nervous but the machine was broken anyway so what harm could I do. It WORKS...

My dish washer is a under the counter type.On mine there are two screws that screw into the bottom of the counter frame,these are located inside when you open up the door, they will be right on the inside and to the very front of the upper part of the door opening. Remove both screws. Now,be slow and start to pull the unit out from under the counter. Make sure you don't scrastch your floor,you may use a towel.If your dish washer's discharge hose is conected under the sink, go ahead and remove it. If your unit can be unpluged, unplug it. If not throw the breaker.Try to turn your unit on' if it does you still have power still on. Try again.With the unit pulled out so you can see the back, lay on your side and look for to long looking plastic nuts with a wire coming out of them. These nuts are holding your eleament in place.Unscrew both nuts and let them slide down the wires. Pull both of the wires off the eleament.now reach inside and remove the old eleament.Put new eleamen in place, reconect wires and tighten the nuts,caustion not to tighten nuts to tight.Ok hook the hose and eleectric back up,push the unit under the cabanet, and install the two screws.Really hopes this helps.