DSD26DHWCBG General Electric Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice dispencer didn't work
per instructions supplied with main electronic control board. was much easier than I thought it might be.
Parts Used:
-
Donald from Montecello, IN
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
broken light switch
Used a small screw driver to remove the damaged switch. Carefully unhooked the two wires and hooked the wires to the new switch. Pushed the new switch into place. Be careful that the wires do not pull back into the refrigerator wall. Took about 15 minutes. Works like New. Easy fix.
Parts Used:
-
Kenneth from Charlotte, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Refrigerator Fresh Food condenser iced-up. Frozen side OK
Had to remove all the covers and fans to expose the condenser, which was difficult as the parts were frozen to it. The styrofoam covering the condenser made it almost impossible to defrost it. Therefore, I ripped the styrofoam off to expose the condenser. Was not really difficult to fix the styrofoam cover using metal tape. Replaced temperature sensor in aluminum block, and used butyl sealant to secure. Had to also re-install parts of ice-ball kit that were not well covered. Lots of parts to keep track of, but anyone could do it.
Parts Used:
-
Dan from Decatur, GA
-
Difficulty Level:Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Installing light switch on refrigerator door
It couldn't be easier. Just pry out the old broken switch with a flat blade screwdriver. start at the bottom in case you scratch the door by accident. When the bottom is out - pull the switch out slowly and disconnect the two wires that are attached to the top, taking care to remember which color lead is connected to which wire. Then, take the new switch and connect the proper wires to their respective terminals and push the switch into the slot. Done!
Parts Used:
-
Martin from Santa Clarita, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Auto dipense of water and ice inop
First determined my modle did not require any of the wire mods descibed on the instructions. Removed power and three cover plate screws. Removed board connectors. Calapsed board anchors and removed board. Removed existing ground wire from board. Installed ground wire on new board and installed board on four mounts. installed connectors and replaced cover and screws. I did wear playtex gloves so as not to cause a static short and wipe out the new board. Took off the bottom panel and cleaned condensor fan cage while I had the fridge out. Secured, plugged in fridge, works real fine, lasts a long time.
Parts Used:
-
James from Broken Arrow, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Did not dispense ice all the time
-
Francine from Dania Beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Small Piece On The Bucket Glide Had Broken Off Making The Motor To Dispense The Ice Non Functional.
My husband used a socket set, took out 4 screws, including the one on the motor where the broken piece was, removed the broken piece, fit the motor back in place, tightened the 4 screws back up. Ice now dispenses. Saved over $100. 00 By ordering & my husband installing the part. Not too bad!
Parts Used:
-
Susan from Delray Beach, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!