DLB1550SBLAD Hotpoint Dryer - Instructions

Used online instructions. Worked well.

I opened the top,by removing the two screws inside the door
on the top. then removed the frount by removing the two 5/16 sheet metal screws inside facing the frount. then pulled the drum out and replaced the berring. Cleaned out the lent from the motor and duckings. Then reasembled.

1. removed old switch 2.wrote model # 3. went to web site found part 4. ordered part 5 part came in 2 days 6. installed part in 15 min. works like new saved over 95.00 thanks ed

My husband and I had taken apart this dryer before, so the second time was a lot easier. The first time we took it apart it took 2-3 frustrating hours. So, if it's your first time, plan for longer.

1. Before we started anything we unplugged the dryer and disconnected the vent.
2. We removed the top and loosened the contol panel on top.
3. We removed the front. Be careful of the wires. You can label them, or just remember where they go.
4. Lay the dryer down on it's back. This make's it easier to remove the drum.
5. Remove the drum, but gently slide the belt off first. Don't stretch the belt removing it.
6. Once the drum was removed, we removed the screws from the inside of the drum.
7. We didn't need to use the entire kit, just the part that sits in the center and spins...kinda looks like a top. (Yes, that's my technical description)
8. We screwed in the new "top" and put the dryer back together.

Really the only part I had to help with (this time)was putting the drum back in to make sure it sat where it was supposed to. It made a big difference that it was laying on it's back...we didn't do that the first time, which was part of our frustration.

Putting the belt back on is a little tricky too. We had instructions still for our dryer to refer to put it back on. If you don't have yours, just google or bing for the instructions. There's website's out there with great pictures.

drive belt gone, replaced belt and bearing

No Problem. Replaced old dryer screen with new one.

All I had to do was take the old filter out and put to new one in. It was easy and took less than a minutes time.

Unfastened 4 screws and lifted the top panel; unfastened 2 top screws, loosened bottom 2 screws holding the front panel,lifted and removed front panel with door. Unfastened 10 screws holding rear access panel, removed panel. Relieved tension on drive belt, removed belt; Removed drum through front of cabinet. Rpelaced rear bushing. Replaced 2 front bearings. Reassembled all components

Removed the top, four screws under the front inside the open door. Then the removed the front, two screws inside at top by drum and two screws on bottom. Then pulled out the drum, from there I was able to get to the bearing that was bad. Mine was a older model than the instructions showed that came with my repair parts but it was colse enough to get the job done. Your website is AWESOME!!! The entire experience was wonderful and made my repair as painless as possible. I have already recomended it to my friends, keep up the great work.

Removed Front of Machine, removed access panel on back of machine, reassembled after installing belt and cleaning out machine. Pretty Easy, hardest part is getting around the front of the drum.This machine has been going since 1978. 31 years, 2nd replacement belt and thats all, not bad, the washer that was bought at the same time went around 6 years ago, havent had the same luck, since then, two machines and the latest one is giving me problems already. They dont make them like they used to.

Removed the screws (torx head) from the top of the control panel and pulled out of the way.
Then remove the top cover gaining access to the inside. Removed two screws near top inside of front panel, 5/16" nut driver. Then removed front wear the front bearing guide is. The old guide was worn thru badly. Removed the bearing guide, snaps out, but it took a little effort. After cleaning installed parts and make sure you secure the felt at the ends. Reassembled in reverse order. The dryer works great now, no clothes are getting eaten and it is much quieter.

Backwards to start- here's the correct way.Disconnect power and vent hose-tip onto front-remove bottom plate allowing access to bottom of dryer and the belt pulleys-remove the small plate in center and under that is a C-clip holding the drum shaft in place-remove the clip and washer-sit dryer upright - open the door and remove the 4 screws under the upper lip which hold the top of the dryer in place-lift up top and secure or have someone hold it up.-inside the top front on both sides are 2 screws per side and there are 2 screws at the bottom under the kick area, remove all 6 of these screws and the front of the dryer will come off-watch the wires-with the front off you can pull the drum forward to allow installing the new belt. - hold the new belt in place with a couple of pieces of tape-reverse the procedure to put drum back together and then thread the new belt onto the drive pulley and under the idler tension pulley.- reinstall back plate, vent hose, power and you're ready to go have a beer.

Removed the screws that hold the draying unit (barrel) to get accest to the back of the switch, and that's when I noticed that I will need the belt and I ordered to when my existing belt goes I have a replacement.

Watched a video online on how to replace the belt, it pretty much told me what to look for to get the drum out. Followed the instructions sent with the bearing kit and removed the old bearing assembly. Ran the screws supplied with the kit into the bearing assembly before I installed it. This was a tip I got off PartsSelect website. Running the screws in first is a must! Had my wife hold the assembly in place while I ran the screws in. That part of the job is the only time you need an extra set of hands. Put the dryer back together and it works like a quiet champ now.

Opened door and found recessed screws that screw into the top of the dry and removed them and then the front removed very easy. Then took of the plate on the back of the dryer to get to the pulley that the drive belt was on and took the belt off the pulley. The dry drum then slid out very easy, there was 2 of use which helped with the ease of getting the drum out. We replace the bearing and the idler pulley wheel. Vaccummed the lent out and then put it back together. Now it is squeek free.