DDE7207SBLAA General Electric Dryer - Instructions

It was super easy, done in 5 less than 5 min. Thanks Parts Select. Parts Select made it easy to find the replacement part by posting pictures. Thanks

Took off console cover (two screws) separated back cover from console cover (4 nutscrews) pulled out two connectors from switch to be replaced and then unscrewed one nut screw. replaced with new unit and reversed processs. 5 minutes. Took another 20 minutes playing with cleaning dust, lint, and having fun restoring console to original shine. Had a lot of fun being my own repairman.

removed top by removing two screw inside door,
found felt was out of place and ruined--found some wear on bearing at rear of drum--decided to
replace these parts plus fround bearing--also
new belt ,since it was apart---to remove the drum
you have to remove front panel,which required
removing two bolts from inside at top--front of
dryer just lays down--then you can pull tub out-
I read other customers repair storys ,which made it real easy.

This kept the interlock open and shut off the dryer when the door swung open The broken latch was popped out using a flat blade screwdriver and the replacement snapped into place by hand. Good as new!

It was a very simple repair. I just opened my box from the mail and pushed the knob into place.

Boyfriend did the repair but it took very little time, the dryer now runs nice and quiet with no thudding and all my clothes are safe from being eaten!

pull top and front of dryer (6 screws), take belt off drum and pull drum out the front of dryer. Take the three star head screws out of stainless heat vent inside of drum and take old bearing housing out of back wall of dryer housing. Pretty much self evident putting everything back in, some trouble installing new bearing housing in back wall of dryer, screws are hard to turn in by hand (new hole). Vacum inside of dryer housing, install everything the way in came out, , plug it in and WA-LA.

Pull old one out stick new one in. Less than 1 minute. Last repair was the water pump that was easy.

i removed two screws and lifted the top up on it hinges. the heating coil was readily accessible. luckly one of the thrmostats fell apart.
partsselect was great. exploded diagrams let me locate and order the replcement easily.

thanks to partsselect i can keep my 16 year old dryer forever.

I repaired it by logging on to parts select website and found the part, waited for about a week or so and opened up the box. I glanced at it and found out that wow it's the exact match except new. Unbelievable and in excitement I went to my laundry room and opened up the dryer and popped that baby right in! Thanks Parts Select

I removed the rear panel to access the drive belt. Lowered the pulley to remove the belt and then took off the front panel and popped the top lid off. The belt was slightly frayed on the edges and looked a little old. Inside of the dryer was filled with lint, noticed the vent that sucks the lint from the dryer was almost totally blocked because off caked on lint. Probably from the moisture when we lived in Tx and had it in our garage. Sucked it out with the shop vac and scraped the rest. Removed the whole drum and that's when I noticed the rear drum bearing was totally destroyed and only a piece or two remained. Ordered the drum bearing and drive belt. I was about to put them on when I saw the drum slides were worn pretty thin. So I had to order more drum slides. That's why it took me so long to repair the dryer. If I had the parts already, it would have only taken an hour or so. I was pretty excited that I did it myself, since my husband usually fixes everything around the house. Easier than I thought :o)

With my hands, a 2 yr old could of done it. But I was amazed how quickly I received the part. Thanks

That happened because the on/off selector nob broke, so I instructed my wife to use a small pair pliers to turn the stem as a work around until I could get to it (6 mos). It eventually broke off. I called a repair service that charges $90 to look at it, but cannot estimate the whole job. The dilemma is that the dryer is over five years old, so a repair costing more than a few hundred dollars is not as reasonable as buying a new dryer. What to do? I ordered the parts and diagrams on the internet. They arrived two days later. The dryer is jammed into a narrow space, so to see the two screws in the back, I needed a small mirror on telescoping wand. To get at the broken switch, I needed unscrew two "star" screws and remove the control panel facing. Not Phillips head, not a common slot head. This star screw is hard to find. I finally located it in the fastener section. I bought a bit that fit my stubby ratchet screw driver. I had to use the stubby screw driver because it was such a cramped space. I finally got at the switch, loosened one screw (hex head) and replaced the two wires on clips - no solder needed. Got a kiss and a squeeze from the missus and a load of clean clothes.

Pulled old lint filter frame out and replaced with new one, very simple. works like new.

I got the parts & a friend did the repair. He removed the "cover" from the top of the dryer to install the new timer. He "plugged" it back in, put the cover back with the screw driver & replaced the knobs & the dryer was good to go. It was much easier than I thought it would be. Getting the parts from you guys was awesome - the delivery was so speedy. If I ever need parts for older appliances that I cannot find at a hardware store, I will most definitely order from you guys.