CSE22GMA Hotpoint Refrigerator - Instructions

Shut off water and disconnected at factory joint at bottom hinge. Unplugged the electrical at the top hinge. Removed the door and installed new bottom hinge and cam assembly. Reinstalled the door and hooked water and electric back up. Part worked fine.

Unplugged frige, removed top shelf, pulled broken fan blade off. Replaced with fan blade just purchased from PartSelect. Very simple repair. Orderd and recieved the right part.

We took the drawers out unsrewed the slide rails, screwed the new ones back on and replaced the drawers. the door cam was alittle harder because we had to lift the door to put it in but it still took under 10 min. altogether it took about 25 minutes. I am also planning on buying a few more parts from the company so I will end up paying about $50 to fix a fridge that I got for free. WHAT A GREAT DEAL!!!!!

This repair replaced two riser cams - one attached to the bottom fridge hinge and one attached to the bottom of the door. The two cams
mate together. So, don't just buy one cam, buy two.
1. Removed all contents off the inside of the door as well as the bins.
2. Unscrewed single screw holding plastic cover over top hinge.
3. Unscrewed 2 screws holding top hinge to the top of the door and removed the top hinge.
4. Pulled door up and off bottom hinge and layed
on floor.
5. Removed plastic grill on bottom of fridge.
6. Removed 2 screws holding bottom hinge in place.
7. Using a vice to hold the hinge, I used a hacksw to cut through the rivet holding the riser cam to the hinge plate.
8. Used a small bolt & nut to secure the new riser cam to the hinge plate.
9. Reattached hinge plate to the bottom of the fridge.
10. On bottom of the door remove two screws holding riser cam to door.
11. Position new riser cam in place and reattach to bottom of door.
NOTE: on my door, the metal SHIM that goes between the cam riser & door was also broken. I ordered the replacement SHIM but it turned out to be made of PAPER. So, I didn't bother putting it on. If the riser cam wears out again, I'll just replace it again.
12. Put door back on and secure the top hinge to the top of the fridge and you're done.

Was able to pull the door up to the normal position, then blocked in place with 2 2x4's. Easily removed the hinge assemble and the door closing cam, which had broken in two.
bolted on the replacement parts in 10 mionutes and the door was a good as new: peice of cake!!!

At first it appeared all was lost since the sales and sevice facility said parts for our GE refrigerator were no longer avalible. We were looking at a $1200 dollar purchase. We decided however to research the internet and see if parts could be obtained. We found Parts Select and to our suprise parts were readily available. We order the drawer side rails and received them within days. The repairs were completed in minutes and for less the twenty bucks.
Steven

took out 4 screws - lowered timer cover - replaced timer- put it back together

It was very simple, took out the slide rails and took a screwdriver and assembled. My wife was very pleased to have these drawers in working order once again.

From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.

Turn of power to fridge. Removed all shelving in freezer section. Unscrewed back panel from freezer area. Removed old defrost term t-stat from top of evaporator coil assembly. Cut existing two wire leads, spliced in new T stat wires. sealed wire splices from water egress and clipped new t-stat in same position as old one. Reassembled rear panel, installed shelves. Turned power back on.That's it.

I removed all items from area of refrigerator. I removed the drawers. I unscrewed the broken slide rail. Upper drawer had left side broken. Lower drawer had right side broken. I simply screwed the new slide rail in. The glass shelf didn't fit, so I took a pair of needle nose pliers and broke off a tiny piece on the slide rail that was preventing the glass from dropping in. (I checked the old one first and could see the same thing had been done) I screwed each rail in and dropped the glass shelf back in. (The lower shelf was broken and I ordered a replacement at the same time as the broken rails. I put the glass into the plastic holder of the old (broken) shelf and slipped it back in. Very easy. I'm a housewife not a repairman. I saved a few dollars on a house call.

First I propped up the door. Then I removed the 2 screws that hold the hinge on. AT this point you do need someone else because the door swings loose. I attached the new bracket and lowered the door. It went verey smooth. I ordered the new bracket after reading the installation stories from others who just repaced the plastic pieces. Its worth the extra money to just put on a new bracket

Since the cam riser was obviously broken I obtained a replacement.
It also broke. The door hinge cam needed to be replaced also.
To repair Remove the hinge cover using a #2 phillips driver. Than remove the Hinge using an 8mm socket. Turn the door upside down and, using an 8mm socket remoge the cam riser and the door hinge cam.
Replace in reverse order.
Be sure to inspect all parts and order all required.

Parts Select made this an effortless process. From finding the part, ordering, to the online diagrams.

I'll be back...

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.