Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken Handle
1. Order part 2. Remove 2 top screws holding vent cover and carefully remove cover 3. Open door all the way and lift, door will come of the microwave 4. Set door on a flat surface facing down 5. You will need a flat screwdriver,carefully set the screwdriver between the door and the black plastic and pry out completely 6. Remove screws holding handle. (This will be a good time to clean the inside of this door) 7. Attach new handle tighten screws 8. Put black plastic back in door and press on all around make sure that is set in place 9. Re-install door and vent.
Removed old fan and replaced with new fan. To replace fan, the over interior fan blade was removed, then the two slip on wires were removed from the old fan motor, then the three screws securing the old fan motor were removed. The process was reversed to install replacement fan
Watching the video showed an easy, unscrew and screw back on process while connecting the wires back. It was really that simple. Once it was complete (not even 10mins), plugged it back in, and its been working great since.
Took off the door, disassembled the door and replaced the springs. I had to retap the holes in the hinge frames as they were not threaded well. Put the door back together, hung it on the stove and the door closes all the way now.
Bake element flashed and left a hole in element. Element was red to blowout point.
Removed power plug from outlet. Removed metal racks. Used 1/4" nut driver to remove screws. Carefully pulled element straight foreword. After wires were exposed they were carefully removed. Made sure wires stayed outside mounting hole. Put new element in made sure wires were secured to new element. Carefully push back on element to get wires in place. Put screws in element. Start one screw then the other. Then tighten both screws. Plug power cord back into wall" or turn circuit breaker on if you used that option. Turn dial to bake element on and check for prerogative operation.
Took bolts out of back of oven ,pull out element had take electric clips off .Then I just plugged in the element ,push in and tighten up bolts. Turn oven on IT Works Yea!!!!!
I unplugged the Stove/Oven electrical cord from the wall, then removed the oven door by unlocking the door brackets with a flat head screw driver then closing the door to the last position before it closes and removing the door from the stove (found instructions on YouTube - very easy, which is optional), then removed the oven racks. Removing the door made it a lot easier to access the broil element and element support bracket screws using a socket wrench. I removed the screws from the rear cover on the back of the stove with a socket wrench to access and disconnect the broil element wires with my hand (pliers if needed). I removed the old broil element and inserted and reconnected the new broil element wires, then re-installed the rear cover. I tightened the broil element in place then re-installed the element support bracket and screws, replaced the oven racks, re-installed the oven door and plugged the stove into the wall. This took about twenty minutes and the broil element is working fine.
A friend came by to help my husband pull out the stove and do the repair. Both had watch the installation video and found it was very helpful and followed the same procedure and had the parts replaced and stove up and running within an hour. Marie
Sensor probe was not sebding proper temp to themostat which regulate the 2 heating elements.
This is a slide in oven fully contained not in a wall, or wood enclosure. I slid the unit out away from the wall unplugged the power cord, used the nut driver to remove a dozen screws, not all of them, you dont need to pull the top back plate off just unscrew the bottom 3-4 screws on the top plate to release the lower back cover plate and you see the probe wire and the insertion point/hole. I actually did not even need to pull the full back plate off but it makes the handling of all the tools and stripping easier. I wish they had just left the plug off of the new probe and had left the 2 loose ends of the 2 wires that had to be spliced, it would have saved 15 minutes just with that part. If you dont have a real splicer tool ya gotta be careful to not cut the wires themselves if you use a sharp knife. Just cut the new probe plug off and splice on the old plug from the bad sensor which obviously you have cut and strip as well as I did and then it fits nicely back together like it was ment to be. I put elect tape on the 2 splices, you could use small wire nuts or whatever you desire, but turn the exposed splices back away from each other and tape them to the insulated wire so no exposed wire is touching any metal then I wrapped the completed taped splices with about a 4x5 piece of aluminum foil to help deflect the residual heat coming from the oven when it is on. put the probe through the hole and placed the metal retainer back in place and re- mounted the back panel plate,cover, that was it problem solved. This entire problem was caused originally in this relatively new oven because people who have been using the oven were sitting heavy pots and pans on the oven door and the hinges were sprung. The door would not stay shut during cooking. I dont know how long this had been going on before I discovered the issue. Once I replaced the hinges ( parts select ) the uneven, wrong temp, extended cooking problem jumped up. I am certain it was related to the open door not shutting for several months. They were using a bungie cord to pull the door closed and not completely. At this point I feel very comfortable with using parts select for all my appliance parts and advice. The folks here at my facility think I am an Einstien but when you have parts select working with you in the background you can't go wrong. I asked a hundred questions and learned alot and saved the facility at least 400 dollars by doing it myself. Thanks to my new work buddy PARTS SELECT. I was really a bit apprehensive about the doors hinges they looked dangerous and might have been but the tech I spoke with at P.S. walked me through it on the phone and I read the blogs which are really helpfull SORRY THIS ONE IS SO LONG.
Removed the oven door, the trim was already cleaned and ready for new glass. Once the new part arrived, I removed it from the shipping container, placed it in the bottom groove of the trim kit and tightened the screws. Then placed the top trim and handle assembly, in place and tightened the screws. Then placed the oven door back on stove.
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door. Just reverse the way you take it apart to put it back together.
removed the door from the range. removed the 4 layers of glass and carefully set aside the unbroken ones. the 3rd and 4th glasses were held together with a metal frame which had to be dismantled. The old broken glass was rusted and hard to get out of the frame. It had to be cleaned thoroughly of broken glass and rust. the removal process could then be reversed to assemble the parts and re assemble the door to the front of the range
