CGLEF379DSE Frigidaire Range - Instructions

PF alarm appeared on display. Noticed clicking when cord was moved. Had arced for some time and melted original block. New part slightly different. Only has 3 lugs, old one had six. Stack using washers provided. Take note of colors before disassembly. Use caution while working through access opening. The edges are sharp. Only tools neede ... Read more d are phillips screwdriver, deep socket for lug nuts. Nut driver optional. Hope this is helpful.

Cut off power at fuse panel. pulled stove out from wall went behind stove removed back panels in area of sensor that I could see from the front side, inside oven. Located sensor from rear & unpluged senser from wiring bundle reached inside oven & removed screws from sensor. Pulled sensor out & threaded wire through hole. Took old & new ... Read more sensors to bench in shop. Plug on new not the same as old. Had to change plug Cut and stripped wires. Wire is very small, need to use a good stripper. Twisted wire together & soldered connection, used shrink wrap to insulate wire. Took part inside and reinstalled in reverse order. Used 1/4 inch nutdriver on total job start to finish.

I called a repair place. They charged $54 to diagnose, (said it needed a new latch motor) then wanted $220 to complete the repair. I checked online prices and did it myself for about 15 minutes work and the latch motor itself ($44?).

Was necessary to uplug the range, pull it away from the wall and remove the back panel sheet m ... Read more etal, then 3 screws that mount the motor. Replace motor, reattach sheet metal. Plug in. Done. Ready to bake cookies.

First we removed two screws under the rim of the range top to open the lid. Lifted the lid and removed the screws from the bracket that holds the elements, Be careful with the clips that hold the element in, if you break them or bend them there aren't any more! Also note which holes they were in, they are marked according to the differ ... Read more ent sizes of elements. Disconnected the wires, needed needlenose pliers to grip them...connected new element, popped it back in place, replaced bracket, closed top ...Easy peasy!!!

Removed the back cover of the range. Removed the knob from the front of the switch. Removed 2 screws holding switch to range. Removed wires one at a time and connected to proper poles on replacement switch and reinstalled new switch on range

Repair was quite easy, as long as you have the instructions for removing the door. The screws that hold the bottom of the door to the fixed hinge are placed into the side of the hinge assembly after removal; this holds the door at a 45 degree angle for easy removal. After that, just place the door on a flat surface and dismantle the door ... Read more from the inside. The inner glass is contained in a metal frame with another piece of glass; this frame comes apart easily using the clips in each side. The door assembles easily after the glass is replaced; just take your time and give yourself enough room to lay out the parts as you go. Good luck!

We removed the old element by removing the screws that attach it to the back of the oven. (make sure to secure the part that plugs into the actual element so that it won't pull into the back of the oven, we used clips to hold it). We removed the old element and placed the new one in position. Pushed the plugs into the element and screwed ... Read more the element into place.
In our case, we had to also order the clock portion of the stove, as the arcing of the element when it burned out, fried the circuit. So we ordered a new clock. It was also simple to do. It is one unit and we simply removed the old clock, writing down where each colored wire went, and put in the new one, attaching the colored wires. Works like new!
We received our parts in 1 day! I priced the repair with an appliance repair service, and figure we saved ourselves @ $150. The parts themselves were $10-$30 cheaper than the repairman quoted us to repair.

Turned power off at electrical panel. Pulled oven away from wall. Removed back cover (6 screws), then unplugged wires from old receptacle. I had to pull the squeeze clips backwards & break them to remove the old receptacle - couldn't squeeze them enough to remove them otherwise. The old receptacle came out through the inside of the oven, ... Read more and the new one snapped in easily from inside the oven as well. Replaced wiring, installed new bulb, restored power & tested. Replaced back cover. Good time to vacuum under/behind where the oven usually lives before sliding it back to the wall.

Flip up top, remove wires and two screws. Replace in opposite way. Turn off power to stove first.

I was selling my home and did not realize that the anti-tip bracket was not originally installed. A home inspection caught the problem and the buyers required that I install one. I could not find the original and obviously the installer never put it in place to begin with. The buyers wanted this resolved within a week so I had to act f ... Read more ast. I could not find one locally so I found what I needed on your website. It arrived in a couple of days and was easy to install. I used the template provided in the kit and drove the screws through the bracket into the wood plate behind the drywall. Pushed the range back in place and that's it. Couldn't get any easier.

The part ordered and received was a direct replacement for the faulty electronic control board. I disconnected the electrical service, removed the back panels, disconnected the electrical connectors (after drawing a diagram with the wire colors clearly identified) before removing the holding screws. I removed the front legend cover from t ... Read more he old part and installed in on the face of the new electronic board. I installed the electronic board, connected the wires and connectors, installed the rear panels and tested the burners and the oven elements. All of the functions worked properly with the new electronic control board and an oven thermometer confirmed the oven temperature to be correct at several settings. The lady-of-the-house is now HAPPY.

Had to reference original owner's manual for instruction(s) on how to remove oven door. Used several "YouTube" videos to reference oven door design (Oven door glass is actually several layers of glass.) After completing about 30 mins of research and finding the right square drive bit, the repair went smoothly and without complications. Th ... Read more e biggest challenge was researching and understanding what part(s) were needed and how to replace them. It seemed liked a lot of work doing the research however it sure beat a $350 repair bill. It cost me $90 and about 1 1/2 hours of total time. Oven works better than ever, thanks parts select for the part(s) and diagram(s) ...

Lifted the oven top, removed the controls cover, slipped the lens into the hole and slid the light holder device onto the lens

Started by replacing element which was clearly broken. Still no heat. So then I changed the oven sensor. Was disappointed that when I received the sensor I had to cut and splice the connector that was on it with the old one that came off the old sensor. Did that and still no heat so I had to buy a new clock/timer. Went to another store fo ... Read more r that because of the connector not being the right type and there was no picture of the clock/timer like the other website. Overall ok, normall troubleshooting steps, just wish I didn't have to cut and splice the connector on the new sensor I purchased from here.

Removed the broken door handle with a screwdriver, replaced the new door handle with a screwdriver. Took less than a couple of minutes to make the repair.