CAW42114GW0 Crosley Washer - Instructions

W10721967 Splutch Cam Kit

Assuming the pulley nut was properly tightened at the factory. I think this problem occurs because of ever-so-slight rounding of the splutch cam teeth from the actuator engaging and disengaging over whatever time frame there is before a clattering noise develops.

When I took off the 13mm nut using the adjustable strap tool, it felt tight to me...Was it put on as tight as it should have been at the factory? Who knows. I don't have the torque specification of this nut on that plastic pulley.

Watch the videos to remove and replace the belt cover and belt, actuator and splutch cam kit.

Pay particular attention to tightening up the nut. I put the pulley on and hand-tightened the nut. I used the adjustable strap tool and before I tightened everything, I pushed up on the pulley to press against the spring pressure in order to mesh the teeth together. After the nut was tight, I repositioned the strap tool and gave it another go, further tightening it. You see earlier that day, I only tightened it up once because I thought it was good and tight. I put everything back and within a half-hour it was clattering again and I could loosen the nut I thought was tight by hand! I fooled myself. That's why I did it twice, and don't be afraid to give it a good second tightening effort. Two weeks now and the wife is currently very happy.

There are a lot of complaints, with these new energy efficient washers, no matter the brand, on the amount of water that is being used, and not properly washing your cloths, while in the wash cycle.
I got this new MayTag washer, and wanted to see it work, for myself, so I can try to correct the problem. But in order to see it work, and fill, the lid has to be open, to observe it working.
To do so, there is a part connected to the lid, called a "STRIKE", that when the lid is down, it activates the electronics, making the washer run.
So, I purchased this strike, to insert it in the washer, so I can observe the washer running, while the lid is open. Very easy, no tools required, just stick it in the slot, where the strike, on the lid goes, when the lid is closed.

My fault completely! I shut a valve off to a spicket that I have in my garage due to a Nebraska winter. The problem turned out to be that my washer was receiving its cold water from the line that I shut off. So it was an expensive lesson to learn after replacing the switch harness and the latch. Water was turned off Ding Dong!

Removed old one (2 screws) slid in place and screwed in.

Royal pain getting the wash plate off. I'm 6 foot 215 lbs with muscular arms( beer belly too) and I could not get it to come off. Put hay bail twine around the edge and pulled up so hard the entire machine came off the ground. Luckily I am married. Yep I pulled one end of the string and her the other and it flew off. Part select was $10 cheaper than whirlpool and was a perfect match. I might order another to have because like stated earlier I'm married. She is married to me and the washer and dryer.

I watched the video and did exactly what they said to do. It was really easy. The key to the success was in the parts that were mailed to me it had a separate piece of paper telling you to "reset" the washer after doing the repair. I missed this when I watched the video. That was a critical part of the repair which required no tools to accomplish.
I have done 6 loads of wash and the washer has not made any crazy noises and hasn't moved!

remove basket and replace drive hub kit

Part fixed it perfectly.

I figured out through the process of elimination that the problem was the rubber plunger that the solenoid opens and closes. I couldn’t fix just the plunger so I replaced the whole water inlet valve and the cold water worked perfectly after that. Even though it was a little tough to diagnose the problem it was very easy to replace the part once I found out what it was that was wrong.

Trying to follow the instructions according to the video was easy enough until the part where I had to remove the control panel for access to the screws holding the inlet valve. I don't have a putty knife, so I had a bit of trouble trying to remove the panel. I found another way. There are screws on the left and right sides which hold the control panel to the side pieces holding it to the body. If you remove the screws and use a pick or flathead screwdriver to carefully pull up on the tabs below the screws while gently pulling the control panel away, it will easily pop off with a rotational movement. The panel is centered into its location via two plastic pins molded into the side panels, so be aware of them and try to avoid breaking them. They'll help you get the panel properly positioned during reassembly, which is simple. You'll see all this easily if you take the time and look. Don't be in a rush. To reassemble, line up the panel with the plastic pins and rotate it into position. The tabs slide easily into position and lock the panel into place. Just don't forget to reinstall the screws. Removing the panel in this manner added a bit of time to the repair, but not a lot. It's still a fast repair overall. Everything else was exactly like in the video. Well, almost. I had no difficulty whatsoever with sliding the new valve into place. But once the job was done the sounds coming from the washer during the filling stages ceased. Turns out the screens in the inlet valve were getting stopped up with lime.

Unscrewed the screws. Lifted the top and supported it. Took back off washer also. Had someone help "recommend ". Was fairly easy to remove old and replace the new suspension. Old springs were wore out. New ones work perfect.

Watched your videos. Knew I didn’t have the strength to do it myself. Contacted my son, he came by and using your instructions( you made me look very knowledgeable) it was done in short order!

Once we put the washer on it's side noticed lots of oil on the floor and in the belt cover area. Replaced belt anyway but issue is the leaking transmission. Starting warranty process since Maytag carries a 10-year part warranty and machine is 6.5 years old. Wish me luck !!!

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

I put the dial to drain and and pressed the pause button for 3 seconds and it drained.
Unplugged the washer from the electrical outlet .
Shut the hot and cold water off. Disconnected and drained them.
Placed the washer on a soft mat on front side exposing the back and bottom of the machine.
Unscrew the metal cover with Philips head screw driver.
Disconnect the drain hose to a bucket or small dish tub .
Remove the belt cover with 5/8 ratchet or wrench.
Using a ratchet or wrench remove the one bolt holding the clutch in place .
Remove the two Philips head screws from the shift mechanism ( looks like clock timer,my memory is failing me right now sorry! ) .
Pull down on bottom gear after removing nut.
Push in and pull down with a flat head screwdriver on the tabs holding the collar in place above the top gear .The collar and gear and spring should come apart.
Install new parts in the same order . Reassemble make sure to use Locktite 242 on the bottom nut holding the gear.
Install belt , belt guard , cover drain hose . Stand machine back up , reconnect all hoses tightly plug machine into electrical outlet and start. Put a smile on your face because you did a great job and saved yourself some money!