Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
water leaking
opened washer removed old damaged part and replaced with new part, losen brackets from hose inlet, removed hose, then fit new hose into tub groves can be very frustrating take your time and be patient, once you get it on, fit over inlet, tighten brackets make sure that seal is secure by turning on the water to fill if no leak the job is done run thru complete cycle to test. Thanks
I removed two screws near the bottom of the front panel and removed the panel by pulling the bottom away from the machine. Inside, I removed two cap screws, one under each front corner of the top panel. The top panel is hinged at the rear. I lifted the top panel from the front, rotated it to the rear and leaned it against the wall behind the machine. It was not necessary to disconnect any wiring. The "U" shaped water injector hose connects to the washer water source with a hose clamp and has a grommet-like end that fits in a round hole in the top of the tub. The hose had cracked and was leaking where it connected to the tub. The new injector hose was a direct replacement and was easy to install.
removed cover, disconnected small water tube and disconnected electrical connections. Reversed above to install new piece. two nutdrivers required. Channel locks for supply hoses.
Looked online and found a video for the repair consistent with a water leak. Two screws to remove the front panel of the washer, loosen two hose clamps, remove belt (by hand) and three screws to remove old water pump. Replaced pump, replaced belt (made sure it was tight, but not too tight), replaced water hoses, placed cover back on the front and I was done. Maybe 15 minutes tops. Very, very easy. Works like a charm and saved probably $100 in labor.
Well I looked on line to see if there were any similialtys to my problem and followed what they had done on their washing machines. I replaced the water pump,the slide control below the motor,and the lid switch.None of these items worked.I called a tech.and he informed me that it sounds like the transmission is bad ,he is coming to my house tonight to take a look at the machine.
I watched a video on you tube repair videos and the repair went fairly easy. But I missed a part near the end of the video and placed a part too close to the shaft and it would not go into the spin mode. After watching the video again I was able to move the part 1/4" and it now works as good as new.
well i first put on 2 new belts because they were worn and smoking. the new belts did not fix the problem. you suggested putting in a new pulley. it went against my better judgement that the pulley was defective. well i put in the new pulley and now the real problem has surfaced. the transmission is not working. now i want to order a new tranny and low and behold it is no longer available. well why did you sell me a $99 pulley when that was not the next part to change after the belts were replaced. now i have a new pulley on a washer that is going to the recycle center as metal trash. well on my part i will reward maytag by buying a ge washer now. plus i will not count on using you as my parts supplier.
Removed front door from washer lifted front of washer off floor and removed belt’s put washer back on floor Removed motor and slide Cleaned and replaced slides and greased put back in washer secured Then lifted front of washer back up replaced new belts and started the washer up worked great put front of washer back on done Great instructions that came with parts
in reassembly, agitation cylce disappeared and went into a slow spin
I put everything back together like video and then did a small wash. The agitation cycle was gone! haha.....it was in a slow rotation and no agitation at all. The video guy seems to turn pulley wheel all the way clockwise till it bottoms out on brake and then he says to put the lug stop washer and screw it in 1/4" to 3/8" behind the tab on pulley and put screw in w/ lock washer. I watched other videos and figured out that was way too much turning on the pulley. I then unscrewed pulley and hand rotated it back on to the point where it barely start to make contact with brake and then I put the lug stop about almost 1/2" back, attached screw and lock washer and gave it a test and wallah! all good!.
The repair itself is fairly simple. However, being 65 years old getting the new valve back into the back opening of the washer and screwed in was a challenge. The clamp on the water connector hose broke and I had to drive to the store to replace it. You may want to consider giving a heads-ups option of ordering hose clamps to DIYers, when you go to order. Also, the instructions that came with the part was not totally accurate. I had to rotate the cylinders outward to connect to the electrical points. But, my machine is pretty old and that may be why. Otherwise, I am very pleased with how quick I received the part and it was exactly what I ordered. My washing machine is back in business. Thank you
Washer was making a loud clunk-clunk-clunk going into spin cycle.
Found main drive belt had a big chunk out of it. Both belts were worn and "gummy". Replaced both belts with belt kit 12112425; no tools needed -- belts are replaced from the bottom. Just tip the washer back to the wall, and there are the belts.. Installation time 5 minutes.
took front panel off had 2 screws, propped up washer in front, took belts off with hands and put new ones on in reverse order One belt was badly cracked. I am 77 year old female, if I can do it, anybody can. great service on getting belts too. Thank you
