Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washer Would Fill With Water But Not Turn On
Removed control assembly found lid switch. Had to unscrew ground wire from warsher popped clip on old switch came right out. Had to play with lid in order to remove. Popped new switch in screwed ground wire. Reinstalled control panel,plugged in and the way it went. Trouble shot with parts direct made it easy and saved me 350 dollars(new washer)
1. Removed back panel. 2. Removed Entire control paned, control and switch units disconnecting wiring assembly from motor. 3 Tilted front and side panel assembly away from frame, tub assembly and motor transmission assembly. 4.Removed cap from top of agitator, removed bolt holding agitator. Removed agitator, this part was tricky since some corrosion on shaft made agitator very difficult to pull off. 4. From bottom of unit disconnected motor/transmission unit from wash tub. 5. Located clutch assembly and removed lock washers. Removed clutch and replaced with new one. ------------------------------------------------------------ Steps 1 thru 3 were unnecessary. All that needed to be done was to removed the agitator assembly. then turn unit on it's side or back and removed motor and transmission from the bottom.
washing machine motor would run but the part that run the transmission was broke
We had to take the motor out and remove the coupling, when putting it back together we had some problems because the washer was on its side and the lid was open. After putting the motor and coupling back together we tried to turn it on, unknowing to us the lid was open so nothing would happen, finally we realized the lid was open. The actual repair was not complicated, just human error made it seem than way
I clean out the fabric softner dispenser on my machine on a regular basis and found the seal split. After looking at several sites to try and find this part, I found this one. Ordering couldn't have been easier and repair only required pulling up the cup for the softner and installing the cap.
I loosened two screws which held the knob panel in place. I undid the two clips holding the cabinet and removed it. The pump has two clips holding it on, I removed those and the pump came free. Taking advice from these forums, I did not remove the hoses attached. I disconnected the wiring harnesses from the motor. The motor has 2 clips also, these being held on with screws. I removed the screws and the clips. THE MOTOR IS HEAVY. You will see the coupling on the "spindle" of the motor. In my case, both plastic pieces were cracked in 2 places. I removed the old coupling and cleaned the "spindles" and lightly regreased. The replacement pieces I ordered were the "improved" ones with the metal insert. They were a tight fit on the motor but I used a socket and hammer. (lightly). Line up the coupling pieces, reattach clips, DONT FORGET THOSE SCREWS HOLDING THE MOTOR CLIPS. Pump goes on next, etc. MAKE SURE ALL WIRING IS RECONNECTED! Cabinet goes back on, large clips holding cabinet to rear of machine go back on. Knob console flipped down and reattached. Plugged it in and I was good to go! This washer is almost ten years old and this is the second time I have been able to bring it back from the dead, the first time being the agitator "dogs" wearing out. THANKS PARTSELECT!
tub tilted forward. Some fill water would miss the tub
Removed cabinet found tub spring had worn thru rear frame, spring was also almost worn thru. Checked suspension springs very very worn at mounting points. Ordered needed parts. All in Stock. First bracket came the next day took 5 days to get the rest 1 part at a time. Forgot to order suspension spring clips, order them next day shipping came the next day . Just because parts are in stock doesn't mean you will receive in a timely fashion if you need parts better order next day freight. Videos, parts diagrams and instruction are great, regular freight is not good
Being female & never working on appliances, it was a challenge for me. I took the spinning unit apart: 1) Outer cap 2) Inner cap 3) Screw, nut & bolt popped out. Rusty & wouldn't lock into place anymore. Ordered nut & washer at about $10 + shipping. Total $17 from MayTag Rec'd right at 7 days via USPS. Used nutdriver/wrench to screw in new bolt w/washer. Wah la! That did it! Washer working great now! Now that I'm a "diy" handy person, I'm ready for my next challenge. Hopefully, none!
Machine delivered without fabric softener dispenser.
Removed the cover where the dispenser would have been installed and snapped the new one in. 5 minutes. When useing the dispenser after adding softener make sure to fill the dispenser with water to dilute and prevent staining.
Unpluged washer. Turned washer on its side, unpluged wire harness to motor. Removed hoses to pump on motor, removed screws and nuts holding motor, then pulled out motor. Popped off old couplings,intalled new, reassembled. Piece of cake!
Unplug washer. Place large old towel in floor at rear of washer. Turn off and disconnect water supply lines and allow to drip dry. Place towel in floor in front of washer. Tip washer forward onto face of washer. Unplug wiring clip connector from drive motor. Remove 2 1/4 inch head screws from spring clips on bottom of motor housing. Slowly rotate clips out of the was to drop motor. Knoch top coupling piece off agitator shaft with screwdriver and light hammer. replace coupling with 5/8 deep well socket as a driver which will fit the metal insert in the coupling and not interfere with the shaft. then drive the other coupling onto the motor shaft using light hammer and drive socket(5/8) deep well. place the rubber shock connector onto the agitator drive piece then slide the motor back into the mount position. rotate the clips vback into place. tighten 1/4 head screws in clips re-attach the wiring harness tip the washer back up onto "feet" re-attach water supply lines tighten appropriately. Plug unit into receptacle and enjoy....
i had to strip the outer housing of the wahing machine apart the remove the motoe from the transmission to get to the coupling. once i recived the coupling( which was very quickly) i just reversed those steps.
I actually didn't remove any of the panels. I tipped the washer at a 45 degree angle to the back and side to release the motor clamps, unhooked the power to the motor and removed the two drain pipes from the motor.
Once I had all of that removed, I was able to pull the motor away from the transmission and put the new coupling pieces on. The hardest part was holding the motor up (it is fairly heavy and cumbersome to hold while the machine is tipped like that). The pieces didn't go on too easily either. It would have been ideal to have at least the front panel off to use a hammer more easily. I did manage to get it on using a socket and a hammer. With some light taps it went on.
Next I put the hoses back on, the power, the bottom motor clamp, and then wrestled for another 30 minutes getting the top motor clamp on.
The clamps are the metal like springs that hook into the transmission and then spring tighten the motor to the transmission. Then there is a little screw that holds it in place... Not easy to see from any angle, and that is where having the front panel off would be ideal.
I've NEVER worked on a washer before and I accomplished this by myself in about 2 hours. I think if you are sure this is the problem, fix it yourself. Best 20 bucks and 2 hours I spent this month by saving a couple hundred on a new washer or repair person.
I removed four srews holding the control panel and laid it to the side, then removed a screw holding the ground on and disconnected the electrical connection. The lid needs to be open to remove the switch. Just remove the switch and reverse sequence. To replace the coupling , I laid over the washer and removed two screws holding the straps connecting the motor to the transmission. After seperating, I pulled off old couplings and reinstalled the new ones on both the motor and transmission. I had to tap couplings on. Then reversed the installation and set backup and tried it out. It worked great.
Raised washer on cinder blocks high enough to get underneath, removed wiring, capacitor (because it got in the way), removed spring clips from pump, removed pump, no water spillage this way. removed clips from motor, removed motor, pulled old broken coupling rubber ring and plastic pieces out, used a spark plug driver to press new ones in place on the gear shaft and motor as they will fit tighter because they have a metal reinforcement that the original did not have, lined up the two halfs and clipped motor back on, cliped pump back on, reconnected wires again, lowered off the blocks and washed a couple loads that night.
