73109 ((AWBCSE2)) LG Refrigerator - Instructions

1. Shut off water to refrigerator. 2. Removed bottom sheet metal cover (6 screws). 3. Removed leaking water inlet valve assembly from refrigerator (1 screw). 4. Remove water inlet tube (loosen nut) and tube back to refrigerator (pull from water valve after remove cotter pin washer). 5. Detach two electrical wire harnesses. 6. Install new water inlet valve assembly to refrigerator (1 screw). 7. Replace both water tubes to water inlet assembly. 8. Re-attach both wiring harnesses. 9. Turn water to refrigerator on. 10. Check for leaks. 11. Re-attach bottom sheet cover (6 screws).

REMOVED 3 SCREWS AND OUT IT CAME UNPLUG THE HARNES AT THE TOP YOUR NONE

Removed ice dispenser and display with small screwdriver from front of the fridge. Pried out the whole piece slowly. This exposed the motor that activates the chute. Plugged in the new motor before any removal to verify the motor was the problem. When it worked, removed old and installed new. 3 screws. Piece of cake.

Unplugged fridge, shut off water supply disconnected water supply from fridge. Remove screws that hold lower cover on back of fridge, removed screws holding valve assembly to fridge. Disconnect two electrical connections, remove black c-clip on out flow water line, lift fitting on outflow line side and pull water line off. Replace with valve assembly in reverse order

I bought the ice assembly motor only, super easy to install, remove the three main screws, lift out assembly, detach the cable. Then remove the screws on the parts, lift the tape, redo everything in reverse and it works flawlessly!

Swapped old one with new one. New one had extra plug not needed.

Took the old one out and put the new one in.

The only tool required was a Phillips screwdriver. I disassembled the old icemaker and unplugged the electrical snap in device. I removed the ground wire. Then reversed the steps in replacing the refrigerator ice maker kit assembly. It took slightly over 30 minutes to remove and replace the ice maker.

First, remove power to the refrigerator.

To replace the ice maker you first have to remove the back mounting assembly, which ice maker is attached to.

Only three Phillips head screws need to be removed: 2 on the bottom and 1 on the back of the ice maker mounting assembly. Do not remove the two diagonal Phillips head screws holding the dispenser motor on the reverse side of the mounting assembly.

As you pull out the mounting assembly to the front you will see a connector on the top inside, which must be unplugged. A narrow standard screw driver will help the connector lock to release; slide the screwdriver tip under the connector lock clip and it will allow the connector to be unplugged.

Once the ice maker mounting assembly is removed and placed on a flat surface it will be self evident as to how to remove and replace the ice maker. The 1” tape might be needed during the cable re-routing process. However you can reuse the original tape required to be removed during the ice maker remove and replace process, if possible.

Reinstall the ice maker mounting assembly in the reverse order it was removed.

Apply power to the refrigerator.

Cycle the ice maker to Off and then back to On. It may take an hour or two before the ice maker produces ice because the temperature inside the ice maker must reach “0” degrees Fahrenheit before it will begin making ice.





Pull the ice maker

Pulled the fridge out.
Unscrewed the back cover and the one screw holding the value assemble.
undid the 2 hoses and replaced the part.

Super SImple/

Removed ice bin
Unscrew the 3 screws.
Lift ice maker for the bottom to remove it but do not pull it until the power is unplug from the part.
Install the new part the same way you removed the old part.
Turn the switch and waiting 48 hours before the ice bin start getting ice

was easy watching youtube video of how to replace whole ice maker, was only 3 screws, remove from the door, a couple of screws hold it to the flat piece, route the wires around the unit, connect the plug as installing it in the door, position it, and tighten 3 screws, that easy

REMOVED 4 SCREWS HOLDING UNIT IT DISCONECTED PLUG TO CONTROLER AND REMOVED IT BY PULLING OUT ON THE BOTTOM FIRST. TO INSTALL SLIDE THE UNIT UP AND IN FROM THE BOTTOM CONNECT THE PLUG AND INSTALL THE SCREWS. THE TOP SCREW HAS A PLASTIC SPACER WASHER. UNIT WILL NOT START TO MAKE ICE UNTILL IT REACHES TEMPATURE, GIVE IT TIME. WATER DESPENSER WILL WORK. CONTROLS ON THE FRONT OF THE DOOR WILL LIGHT UP NORMALY. I REMOVED MINE WHILE WAITING FOR PART TO ARRIVE, 4 DAYS. EVERYTHING WORKED EXCEPT WATER & ICE DESPENSER AND CONTROL DISPLAY ON THE DOOR.

The refrigerator had the above code and when I check on YouTube, it explained that the defrosting was not working properly. It was taking more than 80 minutes to defrost. I ordered the Temperature Sensor first and it was not the issue. I also ordered the Defrost Temperature fuse or the Thermistor. I had to defrost the refrigerator first by using a portable heater to get it done quickly. (See Youtube on how to get to the Defrosting Unit inside the freezer). The Thermistor was the wrong part. I called the Partselect and explained that the part with the heating element is one piece. (Heating Coil Thermistor or Heating Coil). By replacing that piece solved the Error Code issue. I listened to Youtube for the instructions on how to replace the Heater Coil. So if you see the Error Code dH F, you need to replace the Heating Coil, which comes in
one piece and sits on the bottom of the Defrost Element.

I just followed the instruction on the part , and everything was very easy.