Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Small Plastic clip that holds the spline shaft upright in dish tray broken
This part is extremely delicate if put in or if you try and force it on. You will break more than you fix. There is a definite trick and when you know it, the installation is (no pun) a snap. The trick is to place the small plastic in such a position that the only "snap' required for installation is on the heaviest and thickest port of the small part. Then carefully use the pliers to pinch only between the plastic covered bar and the heavy part of the plastic clip...blip, it goes right on. Try it any other way and you will break more than you can fix....
As others have described, this replacement was very easy. The new spray arm is solid plastic instead of rubber (which had deteriorated and was the part that needed replacing). So it should last longer.
You have to keep and reuse the mounting bracket that attaches the spray arm to the upper rack, so don't throw that away!
The replacement was super-easy, and as others have commented, the dishes haven't been this clean for a long time. Well worth it.
I inspected the pump and checked on-line for instructions . I removed the lower panel and the lower dish rack . Removed the washer head from the top of the pump inside the dishwasher . I next unplugged the wiring after disconnectiong the power supply . Next step was to remove the drain hose from the bottom of the pump . Put a towel under it because it's full of water . Unscrew the nipple from the bottom of the pump to allow clearance so it may be removed thru the top . There are four plastic ears that rotate on the base of the pump . Move them into the outboard position and lift the pump out thru the top. I applied some liquid detergent where the pump seal goes and pushed it back in . Installation is the reverse of removal .
I removed the rubber boot on the top of the water dispersal unit ( stainless steel wand ) by turning it counterclockwise and the wand came off with ease. I then removed the top unit under it by removing the 8 torx screws and removed it. Under the unit is a cover with 1 torx screw to be removed and removed the cover to access the unit. I was unable to loosen the 1/4" nut on the shaft as it was very tight so I had to remove the unit and lock the motor armature with a piece of wood and removed the bolt. Using the kit I purchased I installed the new parts as required and it works as good as new.
The whole problem started with the upper vent on the door being plugged up with a whole bunch of labels that had been washed off of a bunch of tin cans that were washed prior to recycling them. Te high water float was also gummed up for the same reason and overflowed on the floor, I pulled it up and out and cleaned it up also, it works as good as new.
My wife noted wood floor bucking up around dishwasher - pulled dishwasher out from counter, tipped it on it's side, looked underneath, & noted slight corrosion on top of motor -
Took motor/pump assembly completely off of dishwasher (comes out from the bottom) by flipping four little plastic cams on motor to the side & then took pump apart (starting at top & working down) till I got to the impeller/motor shaft seal.
Found plastic impeller worn through into two pieces & little spring thingy under the grinder-upper thingy broken.
Ordered Drain & Wash Impeller kit - got it a few days later - installed (new motor shaft seal didn't seem to be quite the same as far as fit, so I didn't use it - just used the impeller & new spring thingy)
Put it all back together & runs fine - no more leaks - (now just have to figure out what to do about warped wood flooring - oh well, it's old & is probably time for whole new kitchen floor anyway)
Note: This particular Kenmore model made by Whirlpool - takes Whirlpool parts.
Note 2: Needed only screwdrivers to do this whole thing - would have been a really quick/easy repair if I had known what the problem was & how it all comes apart. took a little time to figure it out. (I am a rank amateur at dishwasher repair)
Removed dishwasher lower faceplate. Removed hose clamp at the dishwasher end. Removed clamp at the garbage-disposal end. Removed hose. Pulled new hose. Connected both ends of the hose. Installed both clamps. Tested.
Look at the exploded parts diagram, that parts select provides on their website.
You have to take off the nine star pointed screws. So you need a special screwdriver or I had a socket set of them and I used a ratchet to make it easier. I think there are nine of them around the base of the door. Then remove the door and set it on the counter. Flip it over and there is a small plastic cover that has to be removed from the back of it, and it is easily removed by gently pulling on it.
Now comes the difficult part. There is a locking piece on it that holds the latch onto the door by interlocking with a piece on the back side of the door. I took a pair of wire snips and just cut the old interlocking piece off. This way I didn't have to try and slide the two interlocking pieces apart.
When you go to put the new piece on before you interlock them make sure they are put on right. Specifically the latch is pointing the right way to seal the detergent door. Otherwise it can be a pain to separate the interlocking pieces again. (which is why I cut it off the old one).
Disconnect power supply to dishwasher. Open door and remove screws on inner door cover. Carefully remove inner cover while watching how inner parts are arranged. Found return spring on detergent cup linkage had rusted and broken causing detergent cup not to open. Installed new spring and re assembled inner cover. Rotated timer dial one full revolution to check operation of detergent cup. Worked like a charm. Re connect power supply to dishwasher and your good to go.
Top Spray Arm was hitting and would not rotate properly
The mounting bracket was broken.
The parts ordered were a direct match due to the fantastic pictures supplied on this site. A dealer wanted to order it and then I would have had to drive and pick it up - no way.
removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.
it would turn off and on mid-cycle and finally quit completely
I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassembled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!
Diagnosing the problem, i.e. finding the source of the leak, was the hardest part. The best clue was the leak only occurred well into the cycle when the water was hot and steam was coming out the vent. I then assumed there was a bad seal and steam & condensed water was leaking down into the door. I replaced the vent duct & seal, a broken drip cover (an internal part in the door), and replaced a missing rinse aid cap. This stopped the leak.
After doing some research in a repair book I decided to take a stab with a water inlet valve. With expedited shipping I ordered the part and within three days it was delivered. I installed it and the dishwasher seemed like it was trying to fill but still would not. After much cocnsternation I turned the water supply valve to the dishwasher a partial turn to close and I felt the water rush through the valve and the dishwasher then filled. Apparently the shut off valve must have been clogged plus it now leaked. I then replaced the shutoff valve and the copper pipe to the water inlet valve with flexible 3/8" tubing and the dishwasher thus far is running fine without leaks.