Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4KB25G1XTG3 > Instructions

4KB25G1XTG3 KitchenAid Mixer - Instructions

All installation instructions for 4KB25G1XTG3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KB25G1XTG3
46-60 of 139
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

noise in trans.

  • Customer: Leonard from WORTH, IL
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
took it apart. more grease all over. Put in all but one gear on the top. The noise is still there going to try to but the old bearings in and try again. I went back to the old worm gear and allmost all the noise stopped. I did put the new bearings in and the other gears. It seems that the gear on the worm gear was cut wrong. The noise was tear able. I tried the different parts I ordered one at a time. To find out which one stopped the noise. Every time I took a part I had grease all over. It took so long every time I put in a new part to put the trans back together again. I had grease all over.

white plastic part on the lifter handle

  • Customer: ROBERT from LARGO, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Took off all the screws to open the mixer and install the new parts.

Worm gear wore out

  • Customer: Bunny from WAMEGO, KS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Dismantled gear box pulled all gears out and replaced worm gears

Household (stand) mixer making weird noise

  • Customer: Linda from Anchorage, AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed 4 screws on mixer top. Removed 4 screws to gear box cover. Ordered replacement gears from Parts Select. Removed snap ring. Repaced two gears. Applied gear grease, replaced snap ring & screws. Gears at local appliance dealer were $39 each. Total parts from Parts Select + shipping under $20, received in 3 days!

thank you,

  • Customer: Eleanor from Perry, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
my hasband did the work and i an so happy it is working good for me now,

Mixer Feet startarted to disintergrate and leave marks on counter

  • Customer: Vernon from Orange Park, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 1 of 2 people found this instruction helpful
Called original Kitchen Aid and advised had been sold and to look for Kitched Aid on web. Found site, went to appliance diagram and obtained part number and ordered. When parts came in just unscrewed and replaced new feet.

The mixer started getting weak like a gear was stripped and then quite working all together.

  • Customer: Lane from Warrior, AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 3 of 8 people found this instruction helpful
I removed the decorative band that covers the seam by removing 1 screw. I then removed the top portion of mixer by removing 4 square head screws. You will then see the gear housing in the front of the mixer. Remove the 4 screws holding that on. There are no spring that are going to pop out and you never know where they went, but be careful because there is a lot of grease and a gear that it just laying in there on the right side. You will see the stainless shaft with a couple on gear cogs on it. Remove the retaing spring from the shaft and pull the top gear off, it may be a little snug. You will then see the dowel pin, mine was sheared off but I could see where it was. Be sure to remove the broken pieces. Use the punch to knock out the remaining pin. Replace with new pin making sure it is evenly exposed on both side of the shaft. Replace the top gear, then the retaining spring, the the gear housing cover, then the mixer top cover and finally the decorative band. Be sure to unplug before you start. These mixers are expensive and expensive to have someone fix them. I ordered 2 pins because shipping is a little high and the pin is cheap. I fixed this for $17.00 total and have a spare pin.

missing thumb screw on my kitchen aide mixer

  • Customer: Mary Ann from Gilbertsville, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 6 people found this instruction helpful
Dear Customer Service,

I just would like to express my gratitude for your wonderful service. I received my part for my Kitchen aide mixer on time as promised. The part fit perfectly. Thanks you PartSelect for being there.
What a Great Site!

A Happy Customer!

motor would surge after a few moments of running then die.

  • Customer: Fred from Coeur d'alene, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
so easy to remove the switch. I first marked the wires, 1-2-3-4 and then removed them from the old switch. removed the old switch and replaced with the new one and plugged in the wires as per markings. tried it out before replacing the top and it works perfectly. no longer timid about effecting repairs on my own. the diagrams on the website were a great help. this is a great company to do business with. part was here in 3 days.

The mixer only ran on high speed

  • Customer: Kenneth from Clovs, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 6 people found this instruction helpful
I replaced the speed control board, however that did not correct the problem. I received the part very quickly and the install was easy but obviously it did not correct the problem so I will be returning the part. Hopefully that will go well also.

Needed repair

  • Customer: Linda from Ivanhoe, VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
The worm gear was defective. Called the 888 number and received excellent service. Said I would receive a refund and a new one in the mail.

the old housing was plastic and was broken

  • Customer: Robert from Hiawassee, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 9 people found this instruction helpful
the repair was very simple, total time probably 20 minutes.

Broken thrust bearing kit caused damage to the worn gear

  • Customer: Ming from Columbus, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 1 of 4 people found this instruction helpful
Disassambled the gear-train.Removed all broken pieces and grease from gear case. Cleaned gear case and all parts. Reassembled gear-train with new parts and packed all with suitable quantity of new grease. Test run with variable speeds assuming working smoothly.

Plastic gear cover broken

  • Customer: CHRISTINA from NEW GLOUCESTER, ME
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 1 people found this instruction helpful
Removed plastic cover, removed grease and put in new mixer and put new cover back on.

Gears had stripped due to housing crack and movement

  • Customer: Judith from Turtle Lake, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 0 of 1 people found this instruction helpful
Took top apart and installed new housing and two gears. Reassembled
All Instructions for the 4KB25G1XTG3
46-60 of 139