Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 25364802400 > Instructions

25364802400 Kenmore Refrigerator - Instructions

All installation instructions for 25364802400 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 25364802400
91-105 of 331
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Freezer worked, no fridge

  • Customer: Adam from BERKSHIRE, NY
  • Difficulty: Very Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
Removed panel over the motor in the freezer department. Removed screws holding the motor in, unplug wires. Reversed process to install motor.

Coils frozen over. Refrigerator not cooling

  • Customer: Robert from MONTGOMERY, IL
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 1 of 1 people found this instruction helpful
I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!

Refrigerator wasn't getting cold

  • Customer: Brad from STOCKTON, CA
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
removed the back panel of the freezer and unplugged the connector for the Motor. Removed the air diffuser, then removed the fan blade. Removed the 2 screws holding the motor to the bracket. Disconnected the old wire harness and installed the new one. Put the fan blade onto the new motor and installed the motor onto the bracket. Put the air diffuser back on, plugged the motor back in and fastened the back panel. Plugged the refrigerator into the outlet and tested, OK!

Rail that supports meat drawer broke

  • Customer: Kathleen from UHRICHSVILLE, OH
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Unscrewed old rail. Screwed on new one. Replaced drawer. Voila!

None

  • Customer: Edward from DUMAS, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
Real easy took out the broken ones and replaced with the new ones.

Fridge was't cool

  • Customer: Aaron from ODESSA, TX
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
I just followed the instructions on the videos.

Broken

  • Customer: Ellen from FLOURTOWN, PA
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Simple replacement. One screw to be tightened

Evaporator was freezing up and was running non stop

  • Customer: James from PHILADELPHIA, PA
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
I tested the components in the refrigerator defrost function. I used digital multimeter and checked for continuity. Defrost thermostat must 32 degrees or lower.

Fridge and freezer both freezing at bottom and warm at top.

  • Customer: Stephen from PERRIS, CA
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
Unplugged fridge. Removed freezer shelves and unscrewed and removed plastic shelf brackets. Removed the lower rear panel. Removed the bin for ice. Removed the 2 exposed upper rear panel screws. At this point I was able to flex the panel quite enough to access the fan motor. Carefully plugged the fridge back in and turned it on long enough to verify the existing evap. fan motor was not running. Powered off and unplugged again. Removed the fan and it's support assembly, and replaced with new. Had to cut the wires and splice and crimp with the provided wire nuts since the plugs in this model were different. Powered on fridge to check fan function. Reassemble and go home looking' like a hero! Saved my BFF a couple hundred bucks.

replace meat drawer support

  • Customer: Robert from Mansfield, OH
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Removed glass shelf and frame. Unscrewed support from frame,replace with new support and screwed it into the frame, attach drawer and replace shelf in fridge .

Freezer worked, refrigerator didn't. Ice build up on coils.

  • Customer: Salvador from SANTA ANA, CA
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 1 of 1 people found this instruction helpful
Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.

our meat drawer handle was broken

  • Customer: Nickalas A from CUYAHOGA FLS, OH
  • Difficulty: Very Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
I just put the new one in with no problem

FREEZER COMPARTMENT NOT COLD ENOUGH (20 DEGREES)

  • Customer: DANIEL from CAPE CORAL, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
REPLACED TIMER-DEFROST 215846602..REPLACED THERMOSTAT-DEFROST KIT 5303918202..REPLACED CONTROL, TEMPERATURE 5304421256..RECHARGED SYSTEM WITH 134A...ALL FANS WORKING...COMPRESSOR RUNS.. FREEZER STILL NOT GETTING COLD ENOUGH...HOLDING AT 20 DEGREES...ANY SUGGESTIONS..THANKS..DAN

broken meat drawer

  • Customer: gene from pensacola, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
new drawer was received within 2 days and was extremely simple to install.

Plastic support on rail had broken off

  • Customer: Taylor from Greenville, SC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Easy peasy... took the shelf out of the fridge. Unscrewed the old rail. Screwed in the new one. Put the shelf back in. DONE!!!!

My local appliance repair shop said they would have to order the whole shelf in order to fix my problem. It was going to cost $50 and I'd have to wait 3 weeks.

Instead, I found you guys on the internet. The part cost $5 and I got in delivered in 2 days.... CAN'T BEAT THAT!!!!

Thanks
All Instructions for the 25364802400
91-105 of 331