1103401772 Kenmore Dryer - Instructions

Remove top then front panel kit goes on gas value 2 screws hold gas tube in place.

I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke

I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...

Checked fuse with Volmeter, had continuity (acted as a short) not the problem. Disconnected Hot Surface Igniter 2 Position connector to check resistance for a range of 50-300 Ohms of resistance with Voltohm Meter. Meter read open (High Resistance). Removed Igniter by unscrewing 5/16" hex nut on igniter plate assembly and noticed silicon carbide element was cracked in the middle. Ordered a new igniter and noticed assembly was required. Be careful here as igniter element is fragile, also do not touch it with your bare hands. You have to lay down on floor to reinstall igniter assembly and you might want to practice anchoring the defective igniter to gain confidence. Finally with slow movements anchored new igniter assembly and turned on dryer. Watched igniter glow heating gas valve and heating gas flame returned. Dryer fixed for a few hours of study online and cost only $24, plus learned how the gas dryer works.

Unplug from electricity, turn off gas valve, raise top, remove front. Take drum out of cabinet, unhook gas line from burner assy. unhook electric wires, marking them for re installation. Remove, and replace burner tube. Reinstall burner assy attach wires and gas line. (Check for leaks) Reassemble drum to cabinet, rethread belt thru tensioner, reinstall front, let top back down on unit.

We followed the on-line video which was very helpful but it took longer for us. But the part didn't fix the problem, so we had to go back on line and research it some more only to find that the more common cure for our problem was the gas coils which were even easier to replace and that did fix the problem.

I ended up taking the entire dryer apart when I didn't need to, and it turns out it wasn't the Igniter Kit in the first place but the thermal fuse in the back. Was pretty simple to repair in any case however.

Had no definative directions so kind of had to play it by ear. once I got the top and front off the directions that came with the part were spot on. My biggest problem was I guess I was a little over agressive with the drum and I pulled the tension pulley off the bottom. I had to drill a hole and bolt it back down because I couldnt get the little flanges to bend over enough to hold it. It works now but I havent done a load of clothes yet to make sure it will stay together

Followed the easy instructions on the video, and it worked. Sure beats calling a technician.

Replaced igniter

It took me nearly 3 hrs. but I don't do this for a living. Your instruction video was most helpful, madeit easy to know what to do & how to repair dryer. Part Select is top on my list. The site is easy to use & tells you what to replace based on the problem you are experiencing. The instinctual video are the best in the BUZ! Many thanks for making difficult repair much easier. David

Ordered the part, called a friend that is a LP worker. He came over and in less than 15 mins had the new orface and regulator plunger installed and another 10 mins to install new flex pipe and shut off valve and it works great. It was really easy I watched him do it and could of done it myself if I did not have a friend that could do it.

Initially confused by instructions provided in that it stated to loosen a brass coupler. Disconnected power. Removed front bottom panel. Disconnected both leads to ingiter. Removed the 2 screws holding igniter bracket in place. Carefully slid igniter and bracket forward and removed from dryer. Removed screw holding ingiter and replaced with new. Reinstalled in reverse.

I just followed the instructions provided, after taking a long look as to whether it really applied to our dryer. Just take your time and install the unit as you removed it. We removed the unit by first removing gas line, then two screws on the side and it was out. Put on stopper, followed by switching out the orfice.

Removed back panel and tested all components. Everything was good so had to remove front to test last 2 components. Removed front and used brick (handy tool when your working solo) to hold drum up and in place (with full load of damp towels). Defective igniter. Testing all took 10 minutes, replacement took 2. Spent more time opening and putting machine back together than testing and replacement took.