Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Switch Broke...Absolutely Fell Apart.
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
part was substituted, won't work, you did not send my light board
From Donna Turner acct # 190766
I ordered Refrigerator/freezer light board PS11702378
You substituted for a single light module
I troubleshooted and decided to order from your company the light board. You changed my order. I researched what you sent and thought, ok, we'll identify the one light that is out and replace only that...
My paid electrician spend well over an hour inside the frig, and confirmed that all 3 lights in fact work fine, and the problem is above the wiring harness, and what you sent is not correct.
The package has been opened. You substituted my ordered part, it did not remedy the problem, I want a full refund, including S&H
Please advise/sent me Return Authorization, whatever your company policy is.
Steps to replace Whirlpool evaporator fan motor 1. Watch numerous DIY Youtube videos 2. Move frozen food to refrigerator section, close refrigerator door 3. Cut power to refrigerator 4. Remove all shelves and bins in freezer section 5. Back panel has two parts, a top and a bottom section 6. Unclip small shroud covering screw bolt in upper left corner holding top panel. Remove screw bolt 7. Gently pull and work top panel out 8. Remove screw bolts from all four corners in lower panel and remove bottom panel 9. Verify power has been turned off 10. Unclip grounding wire 11. Unclip evaporator fan motor from power 12. Remove whole cradle holding evaporator fan motor. Note orientation of cradle. Fan blade is slightly angled toward the back of freezer. In other models, the cradle may not be removeable. 13. Remove plastic fan with firm pull 14. Unclip bottom brace to remove evaporator fan motor 15. Replace old grommets in bottom brace and on top of evaporator fan motor with the new grommets 16. Install new evaporator in cradle and clip-in the bottom brace 17. Install new fan blade on motor 18. Place cradle with new evaporator fan motor back in freezer 19. Reclip power and ground wire 20. Turn on power and test if working correctly 21. Turn off power 22. Complete steps from 8 to 2 in reverse
It is as easy as is shown in the self-help video. (1) Disconnect the power, (2) Roll the appliance out so you can get to the back, (3) Using a nut driver remove all the screws from the lower back panel then remove the panel, (4) Remove the tensioner wire, (5) unplug the electrical connection to the capacitor, (6) gently but firmly remove the capacitor and starter relay as one unit, (7) preassemble your new capacitor and starter relay as one unit, (8) now simply reverse your steps for installing and you are done! These two parts saved me the cost of a new refrigerator. Almost as easy as changing a light bulb. PS: while you have the panel removed you can do a thorough cleaning with a soft brush and vacuum.
Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced. reassembled the pieces.
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!