My Orders
Simplicity Snow Blower Parts
GET YOUR OFFICIAL Simplicity PARTS TO ENSURE VICTORY
Shop By Appliance
View MorePopular Simplicity Snow Blower Parts
This is an authentic OEM sourced driver belt, not an aftermarket equivalent. It is specially designed for a variety of snow throwers. This is the main drive belt for the unit that will spin the augers. Please make sure to check appropriate diagrams for correct location and application of this item. It is made from durable rubber material and it is sold individually. You would need a set of wrenches to complete this repair.
This is an authentic OEM sourced driver belt, not an aftermarket equivalent. It is specially designed for a variety of snow throwers. This is the main drive belt for the unit that will spin the augers. Please make sure to check appropriate diagrams for correct location and application of this item. It is made from durable rubber material and it is sold individually. You would need a set of wrenches to complete this repair.
Installation Instructions
Kenneth from ALDAN, PA
Refurbishing for next winter season
I replaced the auger belt and drive belt by separating the machine. The auger belt alone can be replaced by simply tilting without separating but the drive belt can not. So after separating the machine, I removed the auger belt by loosening the belt guide and removing the tensioner. I then loosened the nut that secures the drive wheel.
... Read more
This gave me enough play to remove the drive belt from the drive tensioner and then wiggle it from the drive wheel and out of the machine. Install by wiggling the belt back behind the drive wheel until you can slip it on the wheel. pull tensioner pulley out of the way to get the belt on the top pulley. Tighten the nut to secure the drive wheel. Reconnect the machine at the bottom of the auger housing and replace the auger belt, tensioner, and belt guide. Complete by replacing the upper bolts that hold the two parts together. I have not replaced the friction wheel as of yet. My process took 30 - 45 minutes for both belts.
Read less
This Auger Drive Belt is an original part from Craftsman for use with Craftsman Snowblowers. The auger drive belt rotates the auger on the snowblower. The most common reason for replacing the drive belt is when the snowblower auger won't turn.This part is sold individually. Her is a list of tools that are needed to replace the auger drive belt are a 3/8 inch socket, 9/16 inch wrench, adjustable wrench and a clamp.
This Auger Drive Belt is an original part from Craftsman for use with Craftsman Snowblowers. The auger drive belt rotates the auger on the snowblower. The most common reason for replacing the drive belt is when the snowblower auger won't turn.This part is sold individually. Her is a list of tools that are needed to replace the auger drive belt are a 3/8 inch socket, 9/16 inch wrench, adjustable wrench and a clamp.
Installation Instructions
Kenneth from ALDAN, PA
Refurbishing for next winter season
I replaced the auger belt and drive belt by separating the machine. The auger belt alone can be replaced by simply tilting without separating but the drive belt can not. So after separating the machine, I removed the auger belt by loosening the belt guide and removing the tensioner. I then loosened the nut that secures the drive wheel.
... Read more
This gave me enough play to remove the drive belt from the drive tensioner and then wiggle it from the drive wheel and out of the machine. Install by wiggling the belt back behind the drive wheel until you can slip it on the wheel. pull tensioner pulley out of the way to get the belt on the top pulley. Tighten the nut to secure the drive wheel. Reconnect the machine at the bottom of the auger housing and replace the auger belt, tensioner, and belt guide. Complete by replacing the upper bolts that hold the two parts together. I have not replaced the friction wheel as of yet. My process took 30 - 45 minutes for both belts.
Read less
This is an original part from Craftsman for use with Craftsman Snowblowers. The fiction wheel assembly meshes with the friction disc, causing the drive wheel axle to turn. The most common reason for replacing the friction wheel is when the snowblower's wheels don't turn.This part is sold individually. Disconnect the spark plug wire before installing this part. The tools that you will need to replace the friction wheel disc are 3/8" socket, 9/16" socket, adjustable wrench, hammer, 1/2" socket, flat-head screwdriver, and lubrication.
This is an original part from Craftsman for use with Craftsman Snowblowers. The fiction wheel assembly meshes with the friction disc, causing the drive wheel axle to turn. The most common reason for replacing the friction wheel is when the snowblower's wheels don't turn.This part is sold individually. Disconnect the spark plug wire before installing this part. The tools that you will need to replace the friction wheel disc are 3/8" socket, 9/16" socket, adjustable wrench, hammer, 1/2" socket, flat-head screwdriver, and lubrication.
Installation Instructions
Kenneth from ALDAN, PA
Refurbishing for next winter season
I replaced the auger belt and drive belt by separating the machine. The auger belt alone can be replaced by simply tilting without separating but the drive belt can not. So after separating the machine, I removed the auger belt by loosening the belt guide and removing the tensioner. I then loosened the nut that secures the drive wheel.
... Read more
This gave me enough play to remove the drive belt from the drive tensioner and then wiggle it from the drive wheel and out of the machine. Install by wiggling the belt back behind the drive wheel until you can slip it on the wheel. pull tensioner pulley out of the way to get the belt on the top pulley. Tighten the nut to secure the drive wheel. Reconnect the machine at the bottom of the auger housing and replace the auger belt, tensioner, and belt guide. Complete by replacing the upper bolts that hold the two parts together. I have not replaced the friction wheel as of yet. My process took 30 - 45 minutes for both belts.
Read less
Snow blower discharge chute.
Snow blower discharge chute.
This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lubricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.
This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lubricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.
MAKE THIS REPAIR A GUARANTEED WIN
OVER 2 MILLION PARTS TO ENSURE VICTORY
This Ball Bearing is an individually sold, silver/black, metal part. It reduces friction in the spindle assembly between the spindle shaft and the spindle housing. If broken due to wear/fatigue, you will hear a grinding, growling, rumbling or screeching sound, and should replace the part. Refer to your make, model and diagrams to ensure this is the right part for you.
This Ball Bearing is an individually sold, silver/black, metal part. It reduces friction in the spindle assembly between the spindle shaft and the spindle housing. If broken due to wear/fatigue, you will hear a grinding, growling, rumbling or screeching sound, and should replace the part. Refer to your make, model and diagrams to ensure this is the right part for you.
Shear Pins are designed to break off in order to prevent further damage to your machine. Because they are designed to break, we recommend having a few spares on hand. This part is made of metal, is silver, is not part of a kit or assembly, and is sold individually.
A Shear Pin will break when you hit a large chunk or ice or other debris. Once it is broken, it will need to be replaced. You will need pliers to complete this repair.
Customers rate this repair as Easy.
Shear Pins are designed to break off in order to prevent further damage to your machine. Because they are designed to break, we recommend having a few spares on hand. This part is made of metal, is silver, is not part of a kit or assembly, and is sold individually.
A Shear Pin will break when you hit a large chunk or ice or other debris. Once it is broken, it will need to be replaced. You will need pliers to complete this repair.
Customers rate this repair as Easy.
This is an authentic OEM sourced parts kit that is intended to be used with snowthrowers from Murray, Snapper, and Simplicity. The scraper bar attaches to the rear of the bottom of the auger housing to protect the edge of the housing and to collect snow. The flights attach to the auger axle and are used to gather snow into the impeller.
This is an authentic OEM sourced parts kit that is intended to be used with snowthrowers from Murray, Snapper, and Simplicity. The scraper bar attaches to the rear of the bottom of the auger housing to protect the edge of the housing and to collect snow. The flights attach to the auger axle and are used to gather snow into the impeller.
Installation Instructions
Duane from RICHFIELD, MN
Scraper bar and flight worn past wear limit.
Removed scraper bar and support. Removed flight paddles. Several retaining screws were seized requiring WD-40 and vice grips for removal. Torx sockets stripped out due to threads being seized. Hex head cap screws would be better for both scraper bar and flight papples.once the screws were removed I used a tap to clean the threads and appl
... Read more
ied lubricant to minimize future corrosion. Three of the four lock nuts for the scraper bar were either not included or lost in shipping due to poor packing requiring me to purchase replacements.
Overall, the job took longer than it should have due to the additional time required to remove seized screws and acquire replacement lock nuts.
Overall, the job took longer than it should have due to the additional time required to remove seized screws and acquire replacement lock nuts.
Read less
This part is an OEM from Craftsman for use with Snow Blowers. The extension spring is used to provide tension between the link rods, and disconnect arm which slows the riding lawnmower down when the speed control is pushed. The most common reason for replacing the spring is if the drive belt does not have enough tension to engage the auger pulley because the spring is broken. This part is sold individually. The tool that you will need to replace the extension spring is a socket wrench.
This part is an OEM from Craftsman for use with Snow Blowers. The extension spring is used to provide tension between the link rods, and disconnect arm which slows the riding lawnmower down when the speed control is pushed. The most common reason for replacing the spring is if the drive belt does not have enough tension to engage the auger pulley because the spring is broken. This part is sold individually. The tool that you will need to replace the extension spring is a socket wrench.
This is available as an individual replacement part. The auger bearing connects to the auger plate and is made of plastic. If this part becomes broken it will need to be replaced and may require a screwdriver during the installation. It is an OEM Craftsman part directly sourced from the manufacturer for use in snowblowers.
This is available as an individual replacement part. The auger bearing connects to the auger plate and is made of plastic. If this part becomes broken it will need to be replaced and may require a screwdriver during the installation. It is an OEM Craftsman part directly sourced from the manufacturer for use in snowblowers.