Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Philip F - April 19, 2023
Verified Purchase
Skinny But Does the Job Well !
Hard to believe such a thin belt can rotate a dryer drum full of wet heavy clothes. 1st belt lasted 17 years and I only changed it now since I was replacing my noisy drum rollers (the front ones) but the original drive belt still appeared fine !
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.8 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Noise and Squeaking from Front During Drying
Front roller bearings were bad and figured to do the belt while in there. I bought the manual online which was very helpful. ?? Unplug dryer Remove 4 screws behind touch panel Tilt panel forward then up leaving wires attached Rear has 2 screws on the rear ends facing down remove them at ends Lift rear up then
... Read more forward push and top will be freed (keep on top) Front edges have 1 screw each but sharp areas watch Open door and remove x 4 screws then lift up and forward bottom has tabs each end to hold in place Wires for light and switch can stay attached, move front/door to side Exposed will be the drum brace.. I changed the x 2 rollers while the drum brace was in place. To undo the rollers you have to use a wrench to reach in as you use a nut driver to remove then re-install new roller with washer on inside and outside (pay attention when you remove) Remove x 4 small screws..... hold drum inside then lift brace up and forward Have assistance hold drum steady with pressure to the back otherwise you will have to align back to the rear rollers Reach into the bottom for the idle pulley to remove drive belt tension... drive belt is VERY SKINNY and has ribbed side that faces the drum. Reverse the steps..
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Angel
February 6, 2019
When i push the start button, the dryer won't start. It make the noise like is going to but, the drum itself won't spin or turn. I have to spin or turn the drum manually for less then half of a turn in order to works!. i was thinking it could be the drive belt? what seem to be the possible diagnosis, thanks.
For model number DPGT750EC1PL
Hello Angel, Thank you for contacting us. I suggest checking the following part: PS959860 Latch Hook. Good luck with your repair!
Was this helpful?
Thank you for voting!
Bill
February 15, 2022
What length is the dryer drive belt?
For model number DPGT650EH0MG
Hello Bill, Thank you for the question. Very sorry but we do not have the dimensions for this, however we have researched the model you have provided and have confirmed the part you are looking for is PartSelect Number PS959966 and is a guaranteed fit. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Kathy
June 4, 2022
Need Heat Element Kit
For model number PTSD850EMOWW
Hi Kathy,
Thank you for your question. The part number listed under your model number for the heater assembly is PS3499685. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
