This part is the replacement drum support roller for your dryer. The roller is approximately 3 inches in diameter and is sold individually. The main reason to replace the drum support roller is if the...
$63.70
In Stock
Order within the next 9 hrs and your part ships today!
The latch hook is a metal part that helps to keep your appliance's door shut while it is in operation. When you close the door, it works in conjunction with the door catch to hold the door in place. H...
Order within the next 9 hrs and your part ships today!
Questions And Answers for DPGT750GC2PL
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cathy
December 18, 2021
Drier lights then goes out, tumbles but no heat.
For model number DPGT750GC2PL
Hello Cathy, thank you for writing. There are two main options for you to check into. The Thermistor PartSelect Number PS959911 and the Blower Motor PartSelect Number PS960009. We hope this helps.
How do I install this on my Gas dryer model number DPGT750GC2PL? My part arrived yesterday. Is there a video on how to take the back off my dryer?
For model number DPGT750GC2PL
Hello Cathy, Thank you for your inquiry. At this time, we do not have a video on replacing this part, but we have found the following installation instructions for you: First unplug your dryer. To replace the thermistor first remove the screws securing the maintop to the cabinet. Slide the top back and lift up to remove. Then uninstall the screws securing the control panel. Lift up the tabs to detach the control panel from the support bracket and move it out of the way. Remove the screws securing the support bracket so you can remove it from the cabinet. Detach the door switch wire harness. Remove the wire from the retainer and set the bracket aside. Open the dryer door and support the front panel as you remove the screws to release it. Pull the panel forward and lift up to remove. Disconnect the light switch wire harness and the moisture sensor wire harness. Remove the screws from the front bulkhead mounting brackets. Remove the screws securing the duct housing to the blower assembly. Now lift the front bulkhead up and pull it forward to remove. Now reach under the drum and push the idler pulley to release the tension off of the belt and pull the belt off of the motor pulley. Use the belt to help lift out the tub. Depress the tab to release the thermistor wire connector. Remove the mounting screw and remove the thermistor. Install the new thermistor and follow the steps in reverse to put the dryer back together. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
We removed the top and front of the dryer and found that the drum roller bearings had gone out on one side. All this happenend on a weekend with no reair store open. We googled the cut sheet for the dryer, found the part number we needed and ordered the parts (we went ahead and replaced both rollers) from partselect.com. For $70 and our o
... Read morewn labor, we completed the repair by Wednesday evening. I feel certain we saved at least $100 if not more by doing the work ourselves.
Once I figured out how to get into the bottom end of the dryer, it went really smooth. 1. Remove 4 screws from the top panel at the rear of the machine. This allows the top section of the dryer to be lifted up. 2. Under the top section is a plastic cover which covers the drum, this does not need to be removed. There are two sc
... Read morerews in the top which hold the front panel in place, one at the front left top and one at the front right top. remove these two screws. Keep screws seperated, as there are several different types which need to be removed so remeber which go where. 3. Open the dryer door there are four screws which need to be removed. Once these are removed the front panel can be tipped out and the door switch wiring needs to be unplugged to remove the front panel and set aside. 4. Remove the left nylon guide at the bottom front of machine, it is in the way to remove the blower duct. 5. Remove blower housing cover. 6. Reach behind blower housing and disconnect the thyrmister and temperature limit wiring. 7. Remove the blower wheel by removing center nut. It is removed by turning nut clockwise while bracing the wheel with a screw driver so it won't turn. 8. Remove three screws that are behind the the blower wheel. 9. Remove the two base screws that hold the housing to the bottom of the machine. 10. Now you can remove the plastic duct from the machine. 11. remove two screws at the right side og the blower motor. 12. Disconnect wire harness from motor. 13. Lift up on right side of motor bracket and slide to the right. You can now remove the motor and bracket. 14. Remove two clips that hold the motor to the bracket. 15. Install new motor in bracket and replace clips. 16. You can now install the motor and bracket assembly by reversing the order of these steps.
Replaced the control panel, very easy to do. Note: There is a RH and a LH control panel available. The RH or LH refers to placement of the screen and not the position of the machine. Also for troubleshooting, you can replace the suspected bad control panel with the one off the other machine as this panel is tha same for the washer and dry
... Read moreer.