Average Repair Rating: 3.3 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The electronic control board had to be replaced as per Error Codes
Note: unplug washer / shut off circuit breaker, either will work * Remove the top: 3 screws in back of washer. Detach the wires, all color coded and can't be mistaken to fit elsewhere, but be careful, there is a tab which needs to be pushed away for wires to come off of the board. Side wires are color coded, but I took a picture to
... Read moremake sure no mistakes. Remove the ECB by using a screwdriver to push tab away that sticks out toward the back from metal frame then slide part out carefully pushing and gently pulling, may have to wiggle it a bit. Replace new part by putting wires back in it's place. Slide the backside against metal frame and lock in place with a click.
Read less
Hong from GLENVIEW, IL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
3 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brian
April 12, 2018
Had codes f06 and e02 did test 1 and 2 . Tried changing ccu and washer still doesn't work
For model number MHW6000XW0
Hi Brain, Thank you for the question. F06 E02 is a communication error between your MCU and your CCU. You'll want to remove the top panel, the control panel, and then the front panel from the washer to make sure the wire connections to the motor control unit below the tub are all secure. If everything checks good, you'd need to have the MCU replaced, PartSelect Number: PS11753928.Hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Clarence
July 10, 2019
Fo6 and eo1 are flashing
For model number MHW6000XW2
Hello Clarence, Thank you for the question. The F06 error code indicates a communication error between the control boards. I suggest checking all of the wire connectors to make sure everything is secure. You can remove each connector and check for any damage and reconnect. This needs to be done for both boards. After this is done and you plug the appliance back in and the error returns, the issue is one of the boards. In most cases it is the Motor Control Board, PartSelect Number PS11753928. Hope this helps!
Washer is about 5 years old, only 2 people live here, 2 loads of wash per week. Appliance service company has replaced cntrl electric control board and 2 dispenser actuator switches. I have cleaned the connections on the dispenser actuator switch twice over the last two years to get washer going again. Washer has failed again, getting codes f08 e02. I am not getting 120 volts to operate dispenser actuator,what do I do now? Cause of bad connections top hose about 1-1/2 not connected
For model number MHW6000XW2
Hi Paul, Thank you for the question. You can remove the connector from the DI6 terminal on the Main control board. With a multi meter, verify the resistance of the dispenser motor. It should read between 1400 and 1600 ohms across pin 1 and pin 3 of the DI6 connector. If it does not read correctly, check the harness and connections between the CCU and dispenser motor for continuity. If the harness and connections are good, replace the dispenser motor. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
