Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is imp...
This is a door hinge, which allows for your washer door to properly shut during the washing cycle, and open after it is finished. If your door hinge is bent or broken and not allowing the door to shut...
This is a door bellow, also known as a door seal gasket, made for various models of washing machine. This bellow is designed to seal the inner drum of the washer from the outside of the washing machin...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This washing machine cleaner includes three time-release tablets designed to remove odor-causing residues, grime, and buildup from high-efficiency and top-load washing machines. The tablets work by cl...
This is a dryer door hinge cap, also known as a bushing, which is a durable plastic cap that is installed on the door hinge and is used to allow your dryer door to operate smoothly when opening and cl...
This hose attaches to water pump assembly.
NOTE: As per the manufacture if the washer has an Eco Ball, it's no longer needed when the new hose is installed.
The leveling leg locking nut is an OEM replacement fastener for use in dryers and washers. It has a head diameter of 3/8 inches and a thread pitch of 16 threads per inch. The nut secures the leveling ...
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
This part attaches to the door and fits into the door lock when the door closes.
$9.62
In Stock
Order now and your part arrives by May 11
Questions And Answers for MHW6000XG2
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Don Fritch
February 20, 2020
Will not spin water out of clothes when loaded, noisy and shakes
For model number MHW6000XG2
Hello Don, thank you for your question. We would recommend checking a few things to determine what the issue is. The shock absorbers, and counterweights on the front of the drum, as well as the drain tubes that go from the tub to the drain pump. If the unit isn't spinning the clothes in the fast spin, and making noise and shaking the most likely issue are one of those aforementioned parts, or the rear tub bearing. That bearing is only available by ordering the tub assembly. I hope this helps.
1 person found this helpful.
Did this question help you?
Thank you for voting!
Lukasz
January 24, 2025
After my washer runs the bleach dispenser is full of water and my detergent is partially leftover in the tray. I tried cleaning it out but it does not help. Any ideas on which part this might be related to?
For model number MHW6000XG2
Hi Lukasz,
Thank you for your question. If your dispenser is not dispensing detergent, bleach, or fabric softener, you will need to replace the actuator switch. This part is responsible for dispensing these products at various points of the wash cycle and if it is malfunctioning, it will need to be replaced. The part number for the dispenser actuator switch is PS11753574. We hope this helps!
I need the hose insert from the soap drains into the door boot
For model number MHW6000XG2
Hello Shane, thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is part number PS11750867. If you would like assistance placing an order, please contact customer service. Good luck with your repair!
How do we drain the water out of the washer. It's not draining the water out of the clothes.
For model number MHW6000XG2
Hello Enua, thank you for reaching out. Based on our understanding, we would recommend checking the drain hose for any blockage. If the hose is fine, then the issue is most probably with the drain pump, part number PS11752769. It removes water from the washer during the drain portion of the cycle. You may need to replace it to solve the problem. Glad to be of help!
Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.
Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.
The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machi
... Read morene requires brute force.
Once the hose was out I found some bra under wires which is what probably punctured the hose.
Removed the front filter and found a bunch of nails.
Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with a
... Read morell the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.
