If the turntable on your microwave does not rotate, or you can hear a grinding noise, the problem may be with the motor. The motor is typically located below the floor of the oven, and is accessed through the bottom. The motor is normally held in place with a retaining screw and will have two wires attached to it as well. If the motor is making a grinding noise it will need to be replaced. If the motor does not turn, you can check for voltage or continuity with a multi-meter. Make sure the power is disconnected from your microwave before beginning this repair.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Ricardo C - February 9, 2021
Verified Purchase
Easy repair
Perfect fit and part corrected problem. Turntable works like new
★★★★★
★★★★★
Connie P - April 15, 2020
Verified Purchase
Perfect match
Domitec does not carry this replacement part for the convection oven. You are a life saver
Thank you so much
★★★★★
★★★★★
Anthony P - July 26, 2018
Verified Purchase
Microwave turntable part
Good price and fast delivery.
★★★★★
★★★★★
Jamie B - April 11, 2018
Verified Purchase
Arrived fast, easy to install
Arrived fast and was easy to install
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
microwave turn table not working
Removed the phillips screws from the base.
Using a # 10 secure driver, remove the motor. (I recommend obtaining a secure star driver set to be sure you have the right size)
Replace the spacer, which is a separate part from the motor.
Reinstall the spacer and motor.
Reinstall the bottom panel.
... Read more
Enjoy!
Read less
RICHARD from CARY, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave dish would not move back and forth
unscrewed the bottom of the microwave and unplugged old part then took the screw out and put new one in. Super easy!
Susan from HENDERSON, NV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
5 of 12 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Phyllis Vogel
December 2, 2017
Wheel on plastic part that turns micro table around is broken. I need a new device to turn the table. I don't know what you call itphyllis vogel
For model number LMH2016ST
Hello Phyllis, Thank you for your inquiry. It would be called a turntable ring part# 5889W2A012H. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.