Mounted across the upper front of the appliance, the slatted plastic grille covers the vent area while allowing air to pass through. Cracks, warped sections, or broken mounting tabs may leave it loose, create rattling, or expose the space behind it. Replacing a damaged grille restores a secure cover and a neat appearance, while keeping th...Read moree ventilation openings clear for normal airflow during appliance use. This is an OEM part sourced directly from the manufacturer.
Restore visibility in the microwave cavity or over the cooktop with this replacement incandescent lamp. The 30 watt bulb uses a screw base to connect to the light socket and provides illumination when the appliance lighting is activated. A burned out filament may leave the area dark while the microwave continues operating normally. Replac...Read moreing a failed bulb restores light for checking food or viewing the cooking surface below. Disconnect power, allow the lamp to cool, and follow the appliance instructions for access to the bulb. This is an OEM part sourced directly from the manufacturer.
This thermal safety thermostat helps protect the appliance from overheating by interrupting an electrical circuit when temperatures rise above its cutoff point. It senses heat at its mounting location and limits operation to help protect nearby wiring and components. A failed thermostat may prevent heating or leave the appliance unable to...Read more operate. Replacing a faulty unit helps restore the temperature protection needed for normal use. The thermostat works as a safety limit rather than a control for selecting everyday cooking temperatures. This is an OEM part sourced directly from the manufacturer.
This micro-switch is designed for use in your microwave. The function of this part is to monitor the door latch position and communicate to the electronic control board whether the latch is open or closed. If your microwave does not provide heat, or will not start properly, you may need to replace the micro-switch. This part is approximat...Read moreely 1 inch in length and 3/4-inch in width. It is made of black plastic with two metal prongs. This is an OEM part sourced directly from the manufacturer. This part is sold individually. Be sure to disconnect the microwave from the power source before you begin this repair.
This microwave door interlock switch responds to the door latch, helping prevent cooking operation while the door is open. Its small actuator changes the electrical contact when the door opens or closes. A worn or damaged switch may prevent the microwave from starting even when the door is fully shut. Replacing a faulty switch helps resto...Read morere proper door detection within the safety interlock system. Internal microwave components can retain a dangerous electrical charge after unplugging, so disconnecting power alone does not make them safe to handle. This is an OEM part sourced directly from the manufacturer.
This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, an...Read mored replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.
This charcoal filter in manufactured to fit a microwave. It removes food odors from the air circulating through your appliance vent. Youi may need to replace this part if you notice odor when cooking your food or if your filter is clogged. It measures approximately 9.5 inches wide and 3 inches tall, and is black in color.
Exhaust air passes through this microwave vent damper when the ventilation fan runs. The metal flap opens with outgoing airflow to let steam and cooking odours enter the exhaust duct, then closes when airflow stops to help limit outside drafts. A bent, warped, or stuck flap may restrict ventilation or allow air to flow back into the kitch...Read moreen. Replacing a damaged damper helps restore free flap movement and proper exhaust operation, providing a movable barrier at the duct opening between fan uses. This is an OEM part sourced directly from the manufacturer.
Electrical overload protection comes from this microwave time delay fuse, rated at 20 amps and 250 volts. It tolerates brief startup current while opening the circuit during a sustained overload or short circuit. A blown main fuse may leave the microwave without power or prevent it from starting. The fuse cannot be reset and requires repl...Read moreacement once it opens. Internal microwave components can retain a dangerous electrical charge after unplugging, so disconnecting the power cord alone does not make internal handling safe. This is an OEM part sourced directly from the manufacturer.
Secure door closure relies on this black plastic microwave door latch hook. Installed inside the door assembly, it engages the latch openings and operates the safety interlock switches when the door closes. A cracked hook or damaged latch may prevent the door from staying shut or keep the microwave from starting. Replacing a damaged latch...Read more helps restore proper mechanical engagement and door operation. The hook moves with the door release mechanism, allowing the door to open when released and latch again when closed. This is an OEM part sourced directly from the manufacturer.
This genuine OEM light socket provides power to the light bulb in your microwave while holding it in place. This light socket is two pronged and the bulb should screw easily into it. If your light bulb will not light, check the bulb itself and light socket’s connection. If the socket is broken, or faulty it should be replaced immediately....Read more Make sure to remove the high-voltage capacitor from your microwave before beginning this repair.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Microwave would not rotate or heat up food.
52 of 77 peoplefound this instruction helpful.
Joshua from WHITE LAKE, MI
Very Easy
15 - 30 mins
Screw drivers
After watching a few youtube videos, I used a phillips SD to take controll pannel off to access the switches that sense when microwave door is closed. Swapped out all 3 switched and mocrowave works like new. $20 fix (shipping included)
Broken door micro switch. (unit does not start heating)
37 of 68 peoplefound this instruction helpful.
JAMES from BILLINGS, MT
Very Easy
30 - 60 mins
Screw drivers
Unplug the unit before servicing. Need phillips screwdriver. Open door. Use step ladder to access and remove 2 small screws from top of the room air diffuser at top of unit. Slide diffuser slightly to the left to align the diffuser's plastic tab on the left side to rotate toward you. (The wires for the front control panel are at the far l
... Read moreeft side of this difuser, but difuser is slotted for easy removal). Once the difuser is removed you will see 1 screw at the top that secures the pannel cover on the left side of the unit. Remove screw and slide this panel slightly up and out. This exposes the plastic frame that holds the upper and lower door switches. To locate the door switches and observe how they work, close and open the door and watch the door (bayonets) open and close the micro switches. Do the (red) buttons on top of the switches move up and down when the door bayonets push and release? If the buttons do not "pop" up when opened the switch is defective. The switch frame is secured with 2 screws. Remove screws and rotate the unit out for easy access to the micro switch(s). The internal (spring?) on my unit that is suposed to allow the red (visible) button on top of the switch to "pop" up when the door is opened was broken. Carefully pry the switch outward while being careful to lift the plastic holder-piece that holds the switch in place. Be careful, there is a small pin on the frame, so rotate the switch OUT toward you while lifting (carefully) the plastic holder-piece (you will see it on top of the switch). You can use an ohm meter to test the continuity of the switches. But if the buttons don't "pop" they are defective. Replace switch and reassemble.
Read less
Was this helpful?
Thank you for voting!
Vent Grille tabs snapped off
18 of 27 peoplefound this instruction helpful.
Andy from PERRYSBURG, OH
Really Easy
30 - 60 mins
Screw drivers
Repair was easy but you have to remove the screw at the top of the microwave (top left) in order to secure the far left tab with the hole in the tab. Place the grille in place, push to the left and then secure the screw you removed. Just remember that the mounted screw will need to be removed the next time you need access in order to repl
... Read moreace the charcoal filter.