You will need to connect the brown wire to the number 1 terminal and the red to terminal 2. You will need to attach the wires labeled for the two prongs and the third is left and not used.
Ask our experts a question about this part and we'll get back to you as soon as possible!
25 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
January 21, 2018
On the start switch, the knob and the shaft are broken. If the shaft is broken do I still need to replace the entire rotary start switch?
Hello John,
Thanks for your question. Yes, the shaft is a part of the switch itself, so both would need to be replaced.
I hope this helps.
21 people found this helpful.
Was this helpful?
Thank you for voting!
Michele
September 23, 2017
The dryer starts when i turn the knob, but i have to hold the knob to keep it running. As soon as i let go, the dryer stops.
For model number DPSR4483ea1WW
Hi Michele,
Thank you for your question. It sounds like you may need to check this switch with a multimeter to see if it is still working correctly. After removing the switch and touching each probe of your multimeter to the prongs of your switch, press down on the shaft to actuate it. If the meter does not change, then you may have to replace the part. Good luck with your repair.
9 people found this helpful.
Was this helpful?
Thank you for voting!
ANTHONY
April 12, 2018
Looking for replacement start knob its # 29 on diaigram but no part # or part to order from
For model number NVL333GB2WW
Hello Anthony, thank you for your question. The PartSelect part number for the #29 knob is PS264466. Please enter the part number into the site for current price and availability. Good luck with your repair!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Joan
August 13, 2017
Does the start switch go out at once.Or does it act up?
For model number Dwsr48ea1ww
Hello Joan, that is a great question. The shaft on that switch can wear out and cause the knob to slip. If you determine that is not the case then the switch is bad and will need to be replaced. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Bob
January 31, 2018
Old starter has three wire attachments, new replacement has only two. How should I wire the 3 wires into the 2 attachments? Thanks.
For model number DJSR473ET1WW
Hi Bob, Thank you for the question. You will need to attach the wires labeled for the two prongs and the third is left and not used. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Stewart
July 1, 2019
Switch will rotate and dryer turns on, but as soon as the switch is released, the dryer turns off. The original switch and the new switch operate the same. If you “hold” the switch in the “start” position, the dryer works as intended and dries the clothes. We have had the GE washer and dryer for many years without any issues. Please help.
Stewart boal
For model number Ps268305
Hello Stewart, thank you for writing. It sounds as though you need to replace the Rotary Start Switch, but we will need the model number for your dryer to locate the correct replacement. We look forward to hearing back from you.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Lewis
January 8, 2020
I have a GE dpsr473ew0ww dryer when i try to set the time i hear a buzzing sound and it only turns off if the dryer door is open or if i have to timer in the off position. It won't start. This happen all of a sudden after a load of towels. Is this a rotary start switch, i did open the dryer and manually press the white button like the door of the dryer normally would if closed and i saw some sparks of electricity. Is this fixable and how?
For model number 4258308122
Hello Lewis, thank you for your question. We would recommend testing the Rotary Start Switch PartSelect Number: PS268305, high limit thermostat PartSelect Number: PS267900 and the PartSelect Number: PS2344321 door switch. These parts can be tested with a multimeter. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ole
March 6, 2018
Hi my dryer will not start when i turn the knob,maybe it is the thermal fuse?.thank you
For model number dvl223ebiw
Hello Ole, thank you for your question. The issue could be a thermostat on the unit. I would test the Rotary Start Switch Part Number: WE4X881 first as this is one of the most common parts that cause this issue. The thermostats you will want to test are the Control Thermostat Part Number: WE04X10028 the High Limit Safety Thermostat Part Number: WE4X757 and the Thermal Limiter
Part Number: WE04X10094. These parts can all be tested with a multimeter. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tony
January 12, 2018
My rotary start switch has 3 wire connects 2 on top 1 on bottom. Do i need a certain switch, the one i got only has 2 connections.
For model number DBXR453ET3WW
Hello Tony, Thank you for your inquiry. We are showing that this is the compatible rotary start switch for the model number you listed. Hope this helps!
Was this helpful?
Thank you for voting!
Doug
November 7, 2018
On dryer there were 3 wire into switch pt# we4x881, only 2 places to connect on switch, where does the 3rd wire go to ? I have to wires marked for 1-2-3, 1 being top #1 3rd on #2,bottom, but on the 2nd wire no thing to attach too?
For model number DWSR405EB0WW
Hi Doug,
Thank you for your question. There is a video listed with the part on our website that you may reference for more information on how to install it. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Part Videos
Replacing your General Electric Dryer Rotary Start Switch
Customer Repair Stories
Average Repair Rating: 4.5 / 5.0, 27 reviews.
What's this?
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Inop Start switch, holes in lint filter
Switch replacement needs only Torks driver, very simple.
The lint filter arrived damaged. The screen is mangled and the frame is cracked. It may be repairable.
Switch was either stuck in start position or had to rotate full turn to start
Removed four allen head screws to expose inside of panel. Used flat blade screwdriver to raise spring retainer and turned switch counter clockwise to remove.
DERALD from Burleson, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Start knob was broken off flush with switch
I turned off the power, unscrewed the 4 screws from the top of the dryer. I then opened it and turned the switch that was in there counterclockwise exactly as utube video said to do. I then took off the two wires from the old switch. The rotary start switch fix right in where the old one was. I put the panel back together, put on the old knob and turned the power back on! It took less than 15 minutes from start to finish! If I can do it anyone can! Joanne Klinkhammer Cecil, Wisconsin
Joanne from Cecil, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
1 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Start switch broke off
I followed the video instructions. I did have to run to the hardware store to pick up a torx screwdriver but otherwise the instructions were perfect. I generally hire someone to do repairs, but this was too easy! I highly recommend doing this yourself as it is definitely a time and money saver. The website made ordering easy and the part arrived quickly!
Pamela from Atlanta, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
0 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
there was no problem
installation exactly how your directions told me on the computer
Edward from Garrison, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Start switch and knob busted
Just followed the installation video. The only issue with the video was that a phillips screwdriver was specified and I actually needed a torx screwdriver.
T-10 driver to remove panel/expose switches. Screwdriver to lift metal tab and hand rotate switch 45 degrees ccw. Switch comes out. Pull connectors off switch one at at time and put on new switch. Install new switch snap in place. Install panel with t-10.
My husband replaced the rotary start switch that we bought. However, the dryer still would not start. He then tested each remaining switch/dial (before we spent more money on parts) to see if the dryer would start if the electrical connection by-passed that part. None of the top panel switches was the culprit. Then he pulled the door switch. The dryer worked with the switch out, but still connected. He reset each wire, put the door switch back in place, and it failed again. He pulled the switch, added electrical tape to all the connections, and put it back. The dryer works fine now.
Marie from Charlotte, NC
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
5 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not start
The switch made a humming sound when I turned it so I thought that might be the problem. Using the instructions on this Web site I took the top panel of the dryer off (after unplugging it), unplugged two wires leading from the switch (needed pliers for this), and removed the switch unit by rotating it counterclockwise (when behind it). The replacement part came in two days. The installation went a lot quicker-maybe ten minutes.
Ray from Kingwood, TX
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
33 of 37 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Customer Reviews
Average Rating:
★★★★★
★★★★★
20 Reviews
5.0
Filter By Rating:
5 Stars
19
4 Stars
1
3 Stars
0
2 Stars
0
1 Star
0
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Leonard E (Buddy) H - March 19, 2023
Verified Purchase
Rotary switch
the part was correct and made my day
★★★★★
★★★★★
Tom C - October 4, 2022
Verified Purchase
10 minute repair
The part arrived very quickly. The repair only took a few minutes and the dryer is like new.
★★★★★
★★★★★
Taylor C - December 1, 2021
Verified Purchase
easy repair. Worked as expected
easy repair. Worked as expected. Found that was the start of the molehill but after replacing heating element, belt, and belt switch - Dryer is working like a charm
★★★★★
★★★★★
Joseph S - July 16, 2020
Verified Purchase
Easy install
On time delivery
★★★★★
★★★★★
Darren C - May 20, 2020
Verified Purchase
Very easy repair & great service
Part was shipped shortly after ordered. Received within 2 days. Part was exactly as needed.
★★★★★
★★★★★
Lottie B - April 22, 2020
Verified Purchase
Easy repair
My appliance is working perfectly. Item was very expensive
★★★★★
★★★★★
Amy M S - March 25, 2020
Verified Purchase
Easy install quick shipping
I buy from this place as there are video instructions on the product pages and shipping is quick, ordering is easy
★★★★★
★★★★★
Valerie B - May 20, 2019
Verified Purchase
very easy to install!
came quickly, very easy to install. the only reason i gave it 4 stars instead of 5 is that it doesn't quite fit the same as the old one and has already come loose once and i've had to pop it back in. I'll probably have to do that again, but it's a quick fix at least.
★★★★★
★★★★★
Robin J - October 31, 2018
Verified Purchase
pretty easy (even for 2 broke girls) LOL
my sister and I did the repair ourselves; hardest part was getting off the old switch, those wires just didn't want to budge, but she prevailed; had to make an adjustment afterward, because it wasn't quite right the first time, but again, my sister (DIY queen) was able to get it up and running; video was quite helpful.....at least didn't have to resort to the expense of a repairman coming to the house...THANX!
★★★★★
★★★★★
Jane H - September 13, 2018
Verified Purchase
Awesome order
The part I ordered was exactly what I needed and the enclosed link to install the part was an added bonus! I will order all my needed parts from you and recommend others do the same!!
With the Fix app, you can quickly and easily find information on your appliance, along with videos and articles to help you fix it.
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
★★★★★
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
Your Subscriptions
Same-day Shipping
Ships from USA
1 Year Warranty
365 Day Returns
