Make sure you haven't got the discount earlier.
Porcelain Drip Bowl - 8" WB32X5060
Fits your JB600G*J5!
★★★★★
★★★★★
Rated by 3 customers
Really Easy
Less than 15 mins
Ratings submitted by customers like you who bought this part.
$
17.55
In Stock
Get FREE EconoShip on orders over $100! T&C apply
Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
Fits your JB600G*J5!
PartSelect Number PS244785
Manufacturer Part Number WB32X5060
Manufactured by
GE
Troubleshooting
This part works with the following products:
Range, Microwave Oven Combo.
This part works with the following products:
General Electric, Hotpoint, Kenmore.
Part# WB32X5060 replaces these:
AP2028280, 2613, 340527, WB32X5052, WB32X5052A, WB32X5060R
Customer Reviews
Average Rating:
2 Reviews
★★★★★
★★★★★
3.0
Filter By Rating:
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Larry S - October 16, 2021
Verified Purchase
Very easy install
Looks great, perfect fit
★★★★★
★★★★★
Laura S - June 29, 2018
Verified Purchase
wrong part
The parts you recommended were incorrect. I already sent an email and got no reply. I would like to exchange the drip bowls I received for two 6" burner bowls #244398 and two 8" burner bowls #244399. Please let me know how to process the return. My order number is #11139259.Thank you!
July 5, 2018
Hello, Thank you for leaving a review on the . Sorry it had taken us so long to get back to you. We have been a bit more popular then normal and are now able to check our reviews. Checking the order I am showing you have already contacted us to address the issue. Please let us know if there is anything else we can assist you with.
- < Prev
- 1
- Next >
Back to Top
Customer Repair Stories
Average Repair Rating: 4.8 / 5.0, 3 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Small elements were losing heating power and large elements did not work.
I unplugged each element from the terminal it was plugged into and then plugged the new element in. I also replace the drip pans and trim rings while I was at it.
Other Parts Used:
-
Joseph from Guilford, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Element would not heat to max temp.
The interesting part of this story was troubleshooting the problem. Was it the element or the control? Turns out the element was making poor contact, generating excess heat ,which corroded the element contact generating even more heat, and so on and so on until the termional block eventually broke. The repair itself was simple once I s
... Read more
eparated the element from the terminal block. After that I removed the terminal block, one screw, removed the connecting wires, two screws, reversed the procedure to install the the new terminal boplck and element. Before the whole process began I made sure to turn the breaker to OFF.
Read less
Other Parts Used:
-
Alfred from East Northport, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burners Heated Irratically
1. Pulled out drawer
2. Vacuumed dust, etc. under stove
3. Reached under stove to rear and pulled plug
4. Pulled the stove out away from wall so I could get to back
5. Removed 5 screws that retained the back of the control panel
6. One by one, I removed each wire from an old control and pushed it onto the same pin ... Read more on the new control - did same for all 4 burner controls
7. Removed the knobs
8. Removed 2 screws from the front panel for each old control and removed the old controls
9. Pushed each of the new controls into place on the panel and reused screws to secure them in place
10. Cut the long control stems using 2 pliers per instructions to match length of old controls.
11. Used knob adapters provided to mate the old knobs to the new control stems
12. Plugged the stove in and tested the burners
13. Unplugged and replace the panel back with original screws
14. Moved stove back into place
15. The right front burner was the one most used, so I replaced the connector for that burner.
16. That connector came with instructions that I followed - cut the wires to the old connector, splice the wires to the new connector wires using supplied wire nuts and shrink tubing.
17. Plugged the stove back in
18. Replaced drawer - job complete - stove like new
2. Vacuumed dust, etc. under stove
3. Reached under stove to rear and pulled plug
4. Pulled the stove out away from wall so I could get to back
5. Removed 5 screws that retained the back of the control panel
6. One by one, I removed each wire from an old control and pushed it onto the same pin ... Read more on the new control - did same for all 4 burner controls
7. Removed the knobs
8. Removed 2 screws from the front panel for each old control and removed the old controls
9. Pushed each of the new controls into place on the panel and reused screws to secure them in place
10. Cut the long control stems using 2 pliers per instructions to match length of old controls.
11. Used knob adapters provided to mate the old knobs to the new control stems
12. Plugged the stove in and tested the burners
13. Unplugged and replace the panel back with original screws
14. Moved stove back into place
15. The right front burner was the one most used, so I replaced the connector for that burner.
16. That connector came with instructions that I followed - cut the wires to the old connector, splice the wires to the new connector wires using supplied wire nuts and shrink tubing.
17. Plugged the stove back in
18. Replaced drawer - job complete - stove like new
Read less
Other Parts Used:
-
HOWARD from WATERBURY, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
14 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS244785
Manufacturer Part Number: WB32X5060
Manufacturer Part Number: WB32X5060
Brand
Model Number
Description
Kenmore
99121-8
Range
- Kenmore Range/Stove/Oven Model 99121-8(1988) (991218(1988), 99121 8(1988)) Parts
Back to Top
Porcelain Drip Bowl - 8"
$
17.55
In Stock
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.