The surface element, also known as the coil surface element, transfers heat to the area on top of range. The element is 8 inches in diameter. If your surface element does not heat, over heats, or heats inconsistently, replacing this part can be the solution to your issue. To determine whether the element is defective, use a multimeter to test it. Before installing the new element, make sure the drip bowl is properly aligned with the notch of the pan. Insert the new element into the reciprocal at a 40 degree angle. Refer to the instructions provided by the manufacturer for more guidance.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your General Electric Range Surface Element - 8 Inch - 2350W
Troubleshooting
This part fixes the following symptoms:
Element will not heat | Little to no heat when broiling
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Merritt W - May 11, 2022
Verified Purchase
Easy repair
Exactly what I needed and was exactly like the original burner. Thanks
★★★★★
★★★★★
Mary Ann H - November 27, 2020
Verified Purchase
Right part, perfect fit, performs well
I had one coil burner on my stove that seemed to fit poorly because it was bent or warped. On occasion it wouldn’t heat up at all. This new burner plugged in well and heats up quickly. I’m very pleased. I even considered getting a full set of burners so I would have practically a brand new cooktop. However, I realized that at the price of the burners, it would be too costly. The price of the burner seemed a bit expensive, but I am definitely pleased with the one I bought.
★★★★★
★★★★★
John F - June 11, 2020
Verified Purchase
worked as expected
easy repair
★★★★★
★★★★★
BARBARA N - April 26, 2020
Verified Purchase
Fast service - just the part I needed
PartSelect did a great job helping me replace a burned out electric element. The stove is very old and I was not sure about the correct replacement part when I looked at the pictures on the website. When I called for assistance, the agent helped me find the the model number and sent me the correct part - arriving really fast. I would recommend PartSelect to anyone looking for a replacement part.
★★★★★
★★★★★
David J - March 3, 2020
Verified Purchase
Part worked okay!
My stove is up and running.
Had to use old clip to attach your burner to my stove the clip you sent was not the same as original.
★★★★★
★★★★★
Susan F - July 6, 2019
Verified Purchase
Great , worked well,easy fix!
Very easy and didn’t need. A repairman
★★★★★
★★★★★
Gerald G - April 29, 2019
Verified Purchase
Straight replacement
All items ordered arrived in good condition and within four days. This is the same as the other parts I've ordered from PartSelect. The place to go for appliance parts.
★★★★★
★★★★★
Maureen H - April 1, 2019
Verified Purchase
Great Part
Part arrived very quickly and fits perfectly.
★★★★★
★★★★★
Scott G - November 20, 2018
Verified Purchase
8" Surface element
Appliance is back up and running, although after ordering, I found the same element at local store for half the price.
★★★★★
★★★★★
Nancy Lynn C - November 1, 2018
Verified Purchase
Electric burner
The part was easy to order, arrived within a few days, works great and eliminated a great deal of frustration/unnecessary expense for me. Thank you!
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 4.8 / 5.0, 43 reviews.
What's this?
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Needed new replacement surface element and drip pans
Surface element easily unplugged and removed, drip pans lifted out, New drip pans inserted, New 8" surface element and present 6" surface elements Inserted and plugged in.
I had to replace my drip pans as well as the heating elements on all four burners
Very simple to replace, pull off the old element and push in the new one. Not only was it super easy, part select was so easy to work with. I had placed the order wrong, and immediately called customer service. They cancelled my order and placed the new one, refunding my money within 2 business days for the wrong order. Courteous, friendl
... Read morey and prompt. I would highly recommend them! Oh, I forgot to mention that the parts actually fit perfectly, unlike drip pans bought elsewhere. Thank you, Sincerely, Cindy
I Ruined My Burner -- This Was A Solution For Me...
I simply pushed the new burner into hardware. I then tested it to see if it works. . .
DEBRA from DULUTH, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner not working.
I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.
Scott from Dallas, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Terminal block and 8" element shorted
Unpluged range. Removed back cover to access the infinite switches . removed old burner and drip pan. removed terminal block and retaining screw on cooktop. removed terminal block wiring from infinite switch taking care to mind were the wires came from. Install new terminal block and reattached to cooktop . installed new 8" burner and dri
... Read morep pan reinstalled back panel and plug in electrical to unit . tested burner . replaced stove after verifying burner worked
I pulled out the heating coil and pushed in the new coil. I turned the stove top on and heard a sound like "dzzzt". I immediately turned off the burner and waited for it to cool, then pulled it out. The part had a burn melt on one side of the end prong. It turns out that the part that the burner plugs into needs to be replaced. Actually,
... Read morethe stove top is over 20 years old and my landlord will have to replace the whole unit. So it turns out that I didn't need to order a surface element after all, but it was very easy to install!
Read less
Jeannette from Haskell, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Electric stove 8" burner needed to be replaced
Installation took 30 seconds. Your website was easy to use & the part received was just as described. It arrived beautifully wrapped & in just a few days. ABSOLUTELY AWESOME!I will recommend your site to everyone.
LISA from GLENDALE, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
0 of 1 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
3
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Joan
March 26, 2020
I’m trying to find drip bowls for my stove LG is 8 in small not sure. Just need new ones. My stove is electric
For model number ??
Hi Joan,
Thank you for your question. Before we can assist you further we would need the model number from your stove. Here is a link from our website that you may reference on where to find the model number on your appliance, https://www.partselect.com/Find-Your-Range-Model-Number.aspx. If your stove has a bottom drawer where you store pots and pans, pull the drawer out and on the left or right frame, sometimes on the frame where the drawer shuts onto, you will find a tag with both the model and serial numbers on it. We hope this helps. Thank you and have a great day.
5 people found this helpful.
Was this helpful?
Thank you for voting!
Corinne
January 21, 2019
Is this replacement burner a genuine calrod?
Hello Corinne, Thank you for the question. All the parts we sell are OEM genuine parts. Thank you for your inquiry, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Kathy
November 12, 2019
Hi i need a replacement burner for an 8" with the " simmer select feature"
For model number 790.93752102
Hello Kathy, thank you for your question. The larger 8 inch element for this unit is PartSelect Number PS2339242. Please enter the part number into the site for current price and availability. Good luck with your repair!
Was this helpful?
Thank you for voting!
Ben
December 30, 2022
One of the 8" elements on our GE electric stove top is has developed a "hot spot" were it burns a brighter orange than the rest of the element. I figure this is a sign that it needs to be replaced, though it still works. I bought a generic replacement element from my local hardware store, but "legs" of the element where it plugs in were to long so the element would not sit in the drip pan. Is that because it was generic, not OEM?
For model number JP328WK2WW
Hi Ben, thank you for reaching out. Yes, the generic part will not work with your model, you will need to order the compatible part. The part number is PS243868. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
Lavina
July 22, 2023
Looking for a 8" stove top coil burner for my stove I have had for 32 years,
For model number JBP26GP2AD
Hello Lavina, thank you for the question. The surface element, part number PS243868, you have mentioned is compatible with your model. We hope this helps!
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Range","title":"Range","url":"/Range-Parts.htm"},{"position":2,"name":"Element or Burner","title":"Element or Burner","url":"/Range-Elements-and-Burners.htm"},{"position":3,"name":"WB30M2","title":"WB30M2","url":""}]
You added 1 item to your cart
✖
$
Qty:
Total item(s) in cart:
Order Subtotal
$
*Taxes and shipping will be applied during checkout
