Replacing your General Electric Range Surface Burner Switch - 9 Inch
Troubleshooting
This part fixes the following symptoms:
Element will not heat
This part works with the following products:
Range.
This part works with the following products:
General Electric.
Part# WB24T10145 replaces these:
AP4343845, 1473850
Customer Reviews
Average Rating:
★★★★★
★★★★★
2 Reviews
5.0
Filter By Rating:
5 Stars
2
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
0
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Dennis D - July 29, 2021
Verified Purchase
great part and speedy delivert
Excellent part direct fit and replacement with speedy delivery!!! Online exploded view showed mechanics on how to easily remove the part and install new one. This is just the part with no replacement instructions or wiring diagrams. These are standard spade connections you might need a needle nose pliers to pull off the old connections.
Would recommend first time DIY'ers either make a diagram on the connections and wire colors at each connection point or just move the connections from the old part to the new part one at a time. Do not ever pull all the connections off during a repair unless you have an electrical schematic indicating what wire goes where!!!!
★★★★★
★★★★★
John M - March 11, 2019
Verified Purchase
Easy Repair
Only took about 10 Min to replace.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Burner remained on "high" as contacts were fused together
Easy removal of switch and installation of new switch block.
Bruce from HOLMEN, WI
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced the Burned switches
Unplug the stow.(Important!) Remove the knobs pulling out from front of the stove. Remove the 2 screws from each knob. From rear.(3 big 4 small screws to be removed) Removing the 7 screws pull up the upper panel get access to switches. One at a time remove the wiring from old switch attach to new switch. Screw t
... Read morehe upper panel. Install the knobs. Plug the stove. You are done! Thanks to PartSelect for their quick response.
Ask our experts a question about this part and we'll get back to you as soon as possible!
8 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert
January 31, 2019
Will this fix the heating element not maintaining a constant temp? My burner is staying too hot.
For model number JBS55DM5BB
Hello Robert, thank you for your question! Are you referring to one of the elements in the oven, or one of the ones on the stove top? If it is for the stove top, then this is likely the part you will need to replace. Ensure you are purchasing the correct one based on the position the burner is in on the stove! If it is the oven, you will likely need to replace the element itself, or the temperature sensor. We hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Ruthie
August 10, 2017
The switch to my large/small right front burners is broken. Can it be replaced?
For model number JB400DP3WW
Hi Ruthie ,
Thank you for the question. You will need the Dual Burner Control Switch PartSelect Number PS236780.
Hope this helps!
The Front left burner has the small and large burners. The large one does not turn on. I replaced the element twice and it still does not turn on the large burner. What is my next move. Thanks
For model number JB700SN3SS
Hi Nick,
Thank you for your question. If you have replaced the left-front burner and the outer section of the element does not light, the issue may be with the burner switch that controls it or there could be an issue with the wiring or the terminal block. We have included a link from our website that you may reference on how to check these parts. Once you have determined the part you need, please call customer service. We look forward to hearing from you!
Hi all, I have a range and there is a warning light that says the burner is still hot and it won't turn off even after the burners have been off for a long time. Is this the part to get to fix that? thanks!
For model number JPB65DM2BB
Hello Mark, Thank you for the question. The most commonly replaced part is the switch that controls the element that was in use when the light came on. Hope this helps, good luck with this repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Kevin
November 5, 2018
My renter says the switches are sparking when cut on can i replace the switches to correct the problem?
For model number JBS55DM2WW
Hello, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is Part Number: PS1765836 and Part Number: PS1765835 for the switches.The appliance has 2 of each. If you wish to place an order, please feel free to contact customer service and we will be happy to help you!
I have removed the surface burner switch for the left front burner (it doesn't get any power). I see that it is part 19 on your diagram, which is part number wb24t10145. However, when I removed the old one, it has part # wb24t10146 imprinted on it. Are they both the same? Or should I order the same thing that is on the oven, currently?
For model number JB855SP2SS
Hello Amelia, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS1765835. This is the switch GE has listed as the correct part. Hope this helps!
Was this helpful?
Thank you for voting!
Reggie
August 28, 2019
Our stove right front 9” burner is erratic/ very inconsistent in the element staying at a constant temperature. We know the element is good but the switch is probably defective. The question we need answered is what the correct switch for our model stove.? and we would like to order it asap.
please reply
For model number JB620SR6SS
Hello Reggie, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number: PS1765835. Hope this helps!
Was this helpful?
Thank you for voting!
Robert
August 26, 2023
The front left burner would not turn off or reduce in heat. Eventually i got it to turn off after turning it to the off position a couple of times. Then I was able to control the burner temperature. I feel that the burner control might be defective and want to replace it to avoid future problems. The diagram is confusing. Is the required part P/N 1765835 or 2339825 if it's the control that needs to be replaced.
For model number JB660 M2 BB
Hi Robert, thank you for your inquiry. Based on the description that you have provided, we would recommend to replace the burner control switch, part number PS2339825, to fix the issue. It turns the left surface burner on and off and controls how much heat the element produces. Glad to be of assistance!
