Drain Pump Kit 280187

Hello James, thank you for your question! Yes, the whole pump would have to be replaced, the teeth are not sold separately. You would want to order Drain Pump Kit 280187. Good luck with your repair!

Hello Tara, thank you for your question. The Whirlpool washer error code F21 means the washing machine has a “water draining issue”, meaning the drain pump itself, or the drain hose is clogged and the washer is having problems draining the water out. In other words, the washer is taking too long to drain the water out of the tub. If nothing is clogging the unit we would recommend replacing the drain pump. I hope this helps!

Hi John, Thank you for the question. If the noise is only present while spinning, I would be an issue with the tub bearing. The bearing is only sold as part of the Rear Tub Assembly. I looked up the part and it is listed as No Longer Available/Discontinued. There is no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. Hope this helps!

Hello Barb, Thank you for the question. You will want to put your appliance into the diagnostic mode. Before you run a diagnostic test make sure the washer is empty and the control is off and the door is close. Step 1. Push “control/on” Step 2. Select the drain/spin cycle, Step 3. Select the “no spin” by pressing the “spin speed” touch-pad, Step 4. Push “prewash option” four times within five seconds. If prewash option is not present on this model, press “rinse hold” four times within five seconds. C:00 will light up on the display (door should lock if this indication is displayed). If the starting procedure fails, push the pause/cancel touchpad, then repeat the starting procedure. Hope this helps!

Hello Lon, thank you for inquiring. This Drain Pump Kit is the correct replacement for your model and should clear the error. Good luck with your repair!

Hello Mike, thank you for your question. The drain pump for your unit is PartSelect Number PS1485610. Please enter the part number into the site for current price and availability. Good luck with your repair!

Hi Mike thank you for your question. There are a few parts that you could check for this issue. First you should take a look at your belt and pulley for any wear and tear. It could be that your appliance is not spinning as fast as it should be. If those parts are fine then you may want to take a look at your drain pump for being the issue. Good luck with your repair.

Hi Walter, thank you for your question. If you are having an issue with water coming into your tub even when the appliance is off or not supposed to be bringing in water. Then you may need to actually look at your water inlet valve for being the issue. Good luck with your repair.

Hello Ricky, thank you for contacting us, In order for us to locate the correct parts and repair information we will require the model number of the appliance. Once you have located the model number please feel free to resubmit the question and we will be happy to help you. Look forward to hearing from you!

Hi Mike, Thank you for your question. If there is water leaking from the door, the issue may be the bellow sometimes referred to as the door boot seal. The door bellow is used on front load washers to seal between the door and the outer tub. Normal wear and tear can cause the rubber bellow to crack, and foreign objects may tear or rip the bellow and create a leak at the front of the washer. If your washer appears to be leaking near the door area, then you should suspect that the bellow may be the cause. Disconnect your washer from the power source. Open the door and carefully inspect the bellows for signs of damage or for dirt and detergent buildup that may prevent a tight seal to the door. Use caution as sharp foreign objects that can cause tears, are often left in the folds of the bellows and may present a hazard. If you find any of the symptoms above, you will need replacement bellows. If the bellow is not causing the leak, there are some parts that you will need to check to see which one is causing the issue. Here is a link from our website that you may reference on what parts to check, https://www.partselect.com/AdvancedModelSymptoms.aspx?ModelNum=KHWS01PWH0&mfgModelNum=&fkMfgID=3&ModelMasterID=203786&PID=13. I hope this helps. Thank you and have a great day!