Quick Question!

Have you ever purchased from PartSelect.com before?

11740613-1-S-Whirlpool-WP285655-Hose Clamp
11740613-1-S-Whirlpool-WP285655-Hose Clamp 11740613-2-S-Whirlpool-WP285655-Hose Clamp 11740613-3-S-Whirlpool-WP285655-Hose Clamp https://www.partselect.com/Schematics/Maytag/WH8VIOZB.gif

Hose Clamp

Your Price

$5.51
Order within the next 5 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11740613
Manufacturer Part Number WP285655
Manufactured by Whirlpool

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

This part works with the following brands: Kenmore, Whirlpool, Maytag, Amana, KitchenAid, Roper, Magic Chef, Crosley, Admiral, Estate, Inglis, Hoover, Jenn-Air, International, Norge, Speed Queen.

This part works with the following products: Washer, Washer Dryer Combo, Dishwasher, Refrigerator, Dryer, Ice Maker, Food Waste Disposer.

This part fixes the following symptoms:

  • Leaking.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.4 / 5.0, 3 reviews What's this?
1-3 of 3
 

71 of 83 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set, Wrench set
Customer: Stephen from Laveen, AZ

Drive pump leaked

It took some trial and error but overall not a difficult project. 1. Take the front covers off. 2. Undo the pully spring to loosen belt 3. Remove belt off idler pulley wheel and free up belt from the large wheel. 4. Disconect the wiring harness and the hoses. 5. Undo the motor mounting bolts (4) 6. Take motor out of washer and remove the 3 screws holding the pump to the motor. 7. The pump had melted to the shaft and required I chisel the pump off of the shaft. 8. Attach new pump paying attention to where the belt is positioned. 9. Reattach the motor bolts, hoses, and wiring harnes. 10. Attach the belt and test the pump. 11. Put the front back on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

49 of 56 people found this instruction helpful

Parts Used:
Level of Difficulty: Difficult
Time to do repair: More than 2 hours
Tools: Screw drivers, Socket set
Customer: Jeff from Moorpark, CA

Water leak noted on floor at front of washer and at sides

Occasional noted leak became worse and I had a repair service out. Incorrect detection of outer tub seal made so cancelled them and read comments about raising the top. Did so just at start of a rinse cycle to see soapy water shoot from top of syphon break then continue to dribble out through tub empty process--this is what had cause the water to flow down the interior drain hose and out through the side and bottom near the pump.

Ordered all the parts shown here and they arrived just in time for planned work. Did not need or use the clamp and gasket purchased as the gasket was included in the break package and I really like the old-style clamps much better.

Replaced the break and the elbow and put it back together. Things went south on a rinse as water shot out the back hose at the new elbow. I had not realized the size of the new elbow was smaller than the original. Went back to the old elbow but it bothered me that it would still move when the 4 assembly bolt-screws were completely tight.

So far this seems to have worked. There does not seem to be any leaking at all. For those who read this, the job could be done in about and hour for less than I spent if you observe and diagnose properly. It appears that the washer at the end of the Syphon Break wore out and that is what caused the leak.

Thanks much to PartSelect for being in business and to all the posters on this site for helping everyone to get these things done right!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 12 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools:
Customer: BLANCHE from OSSINING, NY

Cracked hose again!

Hired someone. Note: I purchased two (2) hoses and (2) clamps -- this is the third time I am replacing a cracked hose. The manufacturer needs to use better quality and more flexible material for hoses.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11740613
Manufacturer Part Number: WP285655
Brand Model Number Description
Kenmore110088732791Washer Dryer Combo
Kenmore11010202000Washer
Kenmore11010202001Washer
Kenmore11010502990Washer
Kenmore11010502991Washer
Kenmore11010852990Washer
Kenmore11010852991Washer
Kenmore11012202100Washer
Kenmore11012502100Washer
Kenmore11012852100Washer
Kenmore11013202200Washer
Kenmore11013212200Washer
Kenmore11014102300Washer
Kenmore11014112300Washer
Kenmore11014202300Washer
Kenmore11014212200Washer
Kenmore11014222300Washer
Kenmore11014502300Washer
Kenmore11014852300Washer
Kenmore11015732400Washer
Kenmore11015842400Washer - Kenmore Washing Machine
Kenmore11015852400Washer
Kenmore11015862400Washer
Kenmore11015864400Washer
Kenmore11015942400Washer
Kenmore11015942401Washer
Kenmore11015944400Washer
Kenmore11015944401Washer
Kenmore11015952400Washer
Kenmore11015952401Washer