Water Inlet Valve with Thermistor WP22003834 | Official Whirlpool Part | Fast Shipping | PartSelect
Water Inlet Valve with Thermistor – Part Number: WP22003834
Water Inlet Valve with Thermistor – Part Number: WP22003834 Water Inlet Valve with Thermistor – Part Number: WP22003834 Water Inlet Valve with Thermistor – Part Number: WP22003834 https://partselectcom.azureedge.net/Schematics/Maytag/59113.gif

Water Inlet Valve with Thermistor

Product Description

Water Inlet Valve with Thermistor Specifications

This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting

This part fixes the following symptoms:

Will not stop filling with water, Leaking, Will not fill with water, No hot or cold water.

This part works with the following products:

Washer.

This part works with the following brands:

Maytag, Crosley, Amana.

Part # WP22003834 replaces these:

22003834.
Part Videos

Replacing your Maytag Washer Water Inlet Valve with Thermistor

Customer Repair Stories
Average Repair Rating: 3.7 / 5.0, 6 reviews What's this?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Nicholas from Duarte, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Parts Used:
WP22003834
Water would intermittently stop flowing into machine
Unplugged power cord, turned off water and disconnected cold and hot water lines. Removed two screws on bracket at water inlet area on back of washer. removed loose bracket and removed one screw that held water control valve (hot and cold). Unplugged four clipon electrical connections (marked before removal for ease of reconnection) Used flat tip screwdriver to remove hose clip from hose that went from valve into machine. Connected four clip on electrical connections and reconnected intake washer hose to water valve. I put a tiny bit of plumbers grease on plastic valve nipple to make it easier to push nipple into rubber hose. Reattached one screw to anchor valve to metal bracket. Repositioned bracket and attached two screws that anchored it to the washer. Reconnected hot and cold water lines and turned on hot and cold water to check for leaks. Plugged in power cord and started a wash cycle to once again check for leaks before pushing machine back into place. Wife didn't think I was "talented" enough to fix the washer, but I proved her wrong.
53 of 61 people found this instruction helpful.
Was this instruction helpful to you?
Azeem from Clermont, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Parts Used:
WP22003834
The washer was stating NF code in the panel. It was not refilling for the rinse cycle. I had to manually press the button.
Turn the washer to the back. Unscrew the upper right corner water inlet valve. Take it out then replace it with new valve. Then turn your washer on and it will work just like brand new !!!!
14 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Paul from Winnetka, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)
Parts Used:
WP22003834
Had a leak at the top of one of the valve
Ordered the new part from Part Select had very prompt shipment (2 days) printed out someone elses review and followed their steps and it was even easier than they had written so if you get this part simply print the only other "steps" listed because their correct. The only addition i would say is you can use a "nut driver" for the screws as well as the hose clamp which makes it simpler, and definitely mark where you remove the connections so they go back in the same location. Also it may be advisable to remove the big "drum cover" to get easier access to the water hose since it's a little short and difficult to get back on the new valve through the inlet valve hole.It should take you about 15 min to do
11 of 14 people found this instruction helpful.
Was this instruction helpful to you?
Robert from Durango, CO
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
Parts Used:
WP22003834
I stripped the plastic threads on the old water inlet and so I had to replace it.
Unscrew the screws holding the soap/bleach/fabric softner in place. Unscrew the door hinges.Unscrew the white plastic clips that are to the right of the door. These hold the front of the washer in place. Once these are removed, you can pull the front of the washer away from the door opening. It leans out from the top and you can remove the entire piece from the clips that hold it in place at the bottom. Then you can unscrew the screws to the top left and top right that hold the top of the washer in place. Once these screws are removed, you can lift up the top of the washer and lean it back revealing the water inlet valve w/thermister. All the electrical connections are easy clip off/clip on. The hose clamp is the typical screw type.
8 of 19 people found this instruction helpful.
Was this instruction helpful to you?
John from PLACERVILLE, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
Parts Used:
WP22003834
water continued to fill up in the washer when it wasn't being used
I was able to open up the top lid on the washer to gain access to the water inlet valve. I changed it out and now water doesn't continue to fill up the washer when it isn't being used. Problem solved. Great video on how to gain access to the water inlet valve.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Frank from PORTAGE, WI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers
Parts Used:
WP22003834
Hot Water Inlet Valve Stuck open!
After watching the repair video, The job became very easy. Thank you parts select, the only thing i didn't like, was the shipping cost. thought it was a little high for such a small and light part..
1 person found this instruction helpful.
Was this instruction helpful to you?
Customer Reviews
Average Rating:
4 Reviews
4.5
out of 5
Filter By Rating:
  • 5 Stars
    3
  • 4 Stars
    0
  • 3 Stars
    1
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Model Cross Reference

This part works with the following models:

PartSelect Number: PS11739466
Manufacturer Part Number: WP22003834
Brand
Model Number
Description
Crosley
CAH4205AWJ
Washer - Residential
Crosley
CAH4205AWW
Washer - Residential
Maytag
MAH5500BWQ
Washer - Residential
Maytag
MAH5500BWW
Washer - Residential
Maytag
MAH55FLBWQ
Washer - Residential
Maytag
MAH55FLBWW
Washer - Residential
Maytag
MAH6500AWQ
Washer - Residential
Maytag
MAH6500AWW
Washer - Residential
Maytag
MAH7500AWQ
Washer - Residential
Maytag
MAH7500AWW
Washer - Residential
Amana
NAH6800AWW
Washer - Residential